删除.v中不必要的测试代码,全部交由.py控制
This commit is contained in:
@@ -754,64 +754,6 @@ initial begin
|
||||
end
|
||||
end
|
||||
|
||||
`ifdef ENABLE_CODE____
|
||||
/*---------------------------------------------------------------------------------------------------------
|
||||
测试用例
|
||||
1. 设置IP为主站或从站，并读取设置结果，期望：0主，1~4从
|
||||
---------------------------------------------------------------------------------------------------------*/
|
||||
begin:SETTING_DEV_ROLE
|
||||
//设置主站从站
|
||||
$fdisplay(spidata_file, "\n\n测试用例：设置IP为主站或从站，并读取设置结果，期望：0主，1~4从");
|
||||
txBuf[0+3] = 8'h01;
|
||||
spi_trans( (16'h00), (`SPI_WRITE), (1), (`IF_IDX(0)) );
|
||||
|
||||
#1000
|
||||
txBuf[0+3] = 8'h02;
|
||||
spi_trans( (16'h0), (`SPI_WRITE), (1), (`IF_IDX(1)) );
|
||||
|
||||
#1000
|
||||
spi_trans( (16'h0), (`SPI_WRITE), (1), (`IF_IDX(2)) );
|
||||
|
||||
#1000
|
||||
spi_trans( (16'h0), (`SPI_WRITE), (1), (`IF_IDX(3)) );
|
||||
|
||||
#1000
|
||||
spi_trans( (16'h0), (`SPI_WRITE), (1), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-设置完毕，检查接口寄存器");
|
||||
spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(0)) );
|
||||
spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(1)) );
|
||||
spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(2)) );
|
||||
spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(3)) );
|
||||
spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(4)) );
|
||||
/*
|
||||
$display("------------------------------ start! %t", $realtime);
|
||||
_reset_deadline_ind = 1;
|
||||
@(posedge _deadline_ind) #5 begin end
|
||||
$display("------------------------------ End! %t", $realtime);
|
||||
*/
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_ENCRYPTION
|
||||
begin:ENABLE_ENCRYPTION_TESTCASE
|
||||
|
||||
$fdisplay(spidata_file, "\n\n测试用例：加密");
|
||||
`SETTING_ENCRYPTION;
|
||||
spi_trans( (16'h50), (`SPI_WRITE), (17), (`IF_IDX(0)) );
|
||||
spi_trans( (16'h50), (`SPI_WRITE), (17), (`IF_IDX(1)) );
|
||||
spi_trans( (16'h50), (`SPI_WRITE), (17), (`IF_IDX(2)) );
|
||||
spi_trans( (16'h50), (`SPI_WRITE), (17), (`IF_IDX(3)) );
|
||||
spi_trans( (16'h50), (`SPI_WRITE), (17), (`IF_IDX(4)) );
|
||||
|
||||
spi_trans( (16'h50), (`SPI_READ), (17), (`IF_IDX(0)) );
|
||||
spi_trans( (16'h50), (`SPI_READ), (17), (`IF_IDX(1)) );
|
||||
spi_trans( (16'h50), (`SPI_READ), (17), (`IF_IDX(2)) );
|
||||
spi_trans( (16'h50), (`SPI_READ), (17), (`IF_IDX(3)) );
|
||||
spi_trans( (16'h50), (`SPI_READ), (17), (`IF_IDX(4)) );
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_INT_INIT_TEST
|
||||
begin:CHECK_INTERRUPT_SIG
|
||||
$fdisplay(spidata_file, "\n\n测试用例：检查设备的INTERRUPT信号");
|
||||
@@ -919,720 +861,6 @@ initial begin
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_DET1_TEST
|
||||
/*---------------------------------------------------------------------------------------------------------
|
||||
测试用例3
|
||||
---------------------------------------------------------------------------------------------------------*/
|
||||
//嗅探
|
||||
begin:DETECT_DEV_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_DET1_TEST);
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：发送嗅探包，需要在波形文件里检查");
|
||||
|
||||
$fdisplay(spidata_file, "-嗅探前，检查链路状态寄存器");
|
||||
//spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-嗅探");
|
||||
|
||||
`include "detect_pkt.vh"
|
||||
|
||||
// 顺序索引
|
||||
//#50000
|
||||
#1000
|
||||
$fdisplay(spidata_file, "-嗅探后，检查链路状态寄存器");
|
||||
//spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_DET1_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_SET_ADDR_TEST
|
||||
/*---------------------------------------------------------------------------------------------------------
|
||||
测试用例
|
||||
---------------------------------------------------------------------------------------------------------*/
|
||||
begin:SET_ADDR_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_SET_ADDR_TEST);
|
||||
_t_start = $realtime;
|
||||
$fdisplay(spidata_file, "\n\n测试用例：设置顺序索引");
|
||||
$display("index @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
|
||||
|
||||
$fdisplay(spidata_file, "-设置顺序地址前，检查顺序地址");
|
||||
//spi_trans( (16'h0010), (`SPI_READ), (5), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-设置顺序地址");
|
||||
`include "set_addr_pkt.vh"
|
||||
|
||||
//测试
|
||||
`SPI_TRANS( (16'hc0), (`SPI_READ), (6), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(4)) );
|
||||
|
||||
//读写
|
||||
#1000
|
||||
$fdisplay(spidata_file, "-设置顺序地址后，检查顺序地址");
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(4)) );
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_SET_ADDR_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_DET2_TEST
|
||||
/*---------------------------------------------------------------------------------------------------------
|
||||
测试用例
|
||||
---------------------------------------------------------------------------------------------------------*/
|
||||
begin:DETECT_DEV_TESTCASE_2
|
||||
`BEGIN_TESTCASE(`ENABLE_DET2_TEST);
|
||||
//嗅探
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：发送嗅探包，需要在波形文件里检查");
|
||||
|
||||
$fdisplay(spidata_file, "嗅探：使用SM0");
|
||||
$fdisplay(spidata_file, "-嗅探前，检查链路状态寄存器");
|
||||
//`SPI_TRANS( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-嗅探");
|
||||
//设置SM1在写入0x3地址触发enq
|
||||
|
||||
`include "detect_pkt2.vh"
|
||||
|
||||
$fdisplay(spidata_file, "-嗅探后，检查链路状态寄存器");
|
||||
//`SPI_TRANS( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_DET2_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_DET_ERR1_TEST
|
||||
begin:DET_ERR_TEST
|
||||
`BEGIN_TESTCASE(`ENABLE_DET_ERR1_TEST);
|
||||
//嗅探
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：发送错误嗅探包");
|
||||
|
||||
`include "detect_err_pkt.vh"
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
|
||||
$fdisplay(spidata_file, "-检查中断");
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
|
||||
|
||||
$fdisplay(spidata_file, "-清除中断");
|
||||
txBuf[3] = 8'h00;
|
||||
txBuf[4] = 8'h00;
|
||||
txBuf[5] = 8'h00;
|
||||
txBuf[6] = 8'h60;
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-再次检查中断");
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
`END_TESTCASE(`ENABLE_DET_ERR1_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_SMx_SEND1_TEST
|
||||
begin:SM1_SEND_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_SMx_SEND1_TEST);
|
||||
_t_start = $realtime;
|
||||
$fdisplay(spidata_file, "\n单读：使用SM1");
|
||||
$fdisplay(spidata_file, "-SM1：数据包");
|
||||
|
||||
`include "sm1_pkt.vh"
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_SMx_SEND1_TEST);
|
||||
end
|
||||
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_SMx_SEND2_TEST
|
||||
|
||||
begin:SM2_SEND_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_SMx_SEND2_TEST);
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
|
||||
|
||||
$fdisplay(spidata_file, "\n广播读：使用SM2");
|
||||
$fdisplay(spidata_file, "-广播读");
|
||||
|
||||
`include "sm2_pkt.vh"
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_SMx_SEND2_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_SMx_SEND3_TEST
|
||||
begin:SM3_SEND_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_SMx_SEND3_TEST);
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
|
||||
$fdisplay(spidata_file, "\n广播写：使用SM3");
|
||||
$fdisplay(spidata_file, "-SM3广播写");
|
||||
|
||||
`include "sm3_pkt.vh"
|
||||
|
||||
`SPI_TRANS( (16'h0800), (`SPI_READ), (16), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h0800), (`SPI_READ), (16), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h0800), (`SPI_READ), (16), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h0800), (`SPI_READ), (16), (`IF_IDX(4)) );
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_SMx_SEND3_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
|
||||
`ifdef ENABLE_ERR_PKT1_TEST
|
||||
begin:ERR_PKT1_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_ERR_PKT1_TEST);
|
||||
//嗅探
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：发送错误数据包1");
|
||||
|
||||
`include "err_pkt1.vh"
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
|
||||
$fdisplay(spidata_file, "-检查中断");
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
|
||||
|
||||
$fdisplay(spidata_file, "-清除中断");
|
||||
txBuf[3] = 8'h00;
|
||||
txBuf[4] = 8'h00;
|
||||
txBuf[5] = 8'h00;
|
||||
txBuf[6] = 8'h60;
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-再次检查中断");
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
`END_TESTCASE(`ENABLE_ERR_PKT1_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_ERR_PKT2_TEST
|
||||
begin:ERR_PKT2_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_ERR_PKT2_TEST);
|
||||
//嗅探
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：发送错误数据包2");
|
||||
|
||||
`include "err_pkt2.vh"
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
|
||||
$fdisplay(spidata_file, "-检查中断");
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
|
||||
|
||||
$fdisplay(spidata_file, "-清除中断");
|
||||
txBuf[3] = 8'h00;
|
||||
txBuf[4] = 8'h00;
|
||||
txBuf[5] = 8'h00;
|
||||
txBuf[6] = 8'h60;
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-再次检查中断");
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
`END_TESTCASE(`ENABLE_ERR_PKT2_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_ERR_PKT3_TEST
|
||||
begin:ERR_PKT3_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_ERR_PKT3_TEST);
|
||||
//嗅探
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：发送错误数据包3");
|
||||
|
||||
`include "err_pkt3.vh"
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
|
||||
$fdisplay(spidata_file, "-检查中断");
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
|
||||
|
||||
$fdisplay(spidata_file, "-清除中断");
|
||||
txBuf[3] = 8'h00;
|
||||
txBuf[4] = 8'h00;
|
||||
txBuf[5] = 8'h00;
|
||||
txBuf[6] = 8'h60;
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-再次检查中断");
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
`END_TESTCASE(`ENABLE_ERR_PKT3_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
|
||||
/*---------------------------------------------------------------------------------------------------------
|
||||
测试用例
|
||||
1. 交换数据sm0~sm7
|
||||
2. 交换数据sm0~sm7
|
||||
3. 交换数据sm0~sm7(中断、状态)
|
||||
4. 交换数据sm0~sm7(R/W/RW, BR/BW/BRW)
|
||||
4. 寄存器单读/写/读写，寄存器广播读/写/读写
|
||||
5. 以上交换数据的错误形式
|
||||
---------------------------------------------------------------------------------------------------------*/
|
||||
`ifdef ENABLE_EXCHG_DATA_SEQ0_TEST
|
||||
begin:EXCHG_DATA_SEQ0_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_EXCHG_DATA_SEQ0_TEST);
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：交换数据sm0~sm7");
|
||||
$display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
|
||||
|
||||
`include "seq_0_pkt.vh"
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_EXCHG_DATA_SEQ0_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_EXCHG_DATA_SEQ1_TEST
|
||||
begin:EXCHG_DATA_SEQ1_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_EXCHG_DATA_SEQ1_TEST);
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：交换数据写dev2_sm0/dev1_sm2/dev3_sm4/dev4_sm6");
|
||||
$display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
|
||||
|
||||
`include "seq_1_pkt.vh"
|
||||
|
||||
`SPI_TRANS( (16'h1800), (`SPI_READ), (64), (`IF_IDX(1)) );
|
||||
$fdisplay(spidata_file, "-嗅探前，检查链路状态寄存器");
|
||||
//`SPI_TRANS( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-嗅探");
|
||||
//设置SM1在写入0x3地址触发enq
|
||||
|
||||
`include "detect_pkt.vh"
|
||||
|
||||
$fdisplay(spidata_file, "-嗅探后，检查链路状态寄存器");
|
||||
//`SPI_TRANS( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
`SPI_TRANS( (16'h0800), (`SPI_READ), (64), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h2800), (`SPI_READ), (64), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h3800), (`SPI_READ), (64), (`IF_IDX(4)) );
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_EXCHG_DATA_SEQ1_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_EXCHG_DATA_SEQ2_TEST
|
||||
begin:EXCHG_DATA_SEQ2_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_EXCHG_DATA_SEQ2_TEST);
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：交换数据读dev1_sm1/dev2_sm3/dev3_sm5/dev4_sm7");
|
||||
$display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
|
||||
|
||||
`include "seq_2_pkt.vh"
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_EXCHG_DATA_SEQ2_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_EXCHG_DATA_SEQ3_TEST
|
||||
begin:EXCHG_DATA_SEQ3_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_EXCHG_DATA_SEQ3_TEST);
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：交换数据读写");
|
||||
$display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
|
||||
|
||||
`include "seq_3_pkt.vh"
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_EXCHG_DATA_SEQ3_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_BC_R_TEST
|
||||
|
||||
begin:EXCHG_DATA_BC_R_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_BC_R_TEST);
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：广播读");
|
||||
$display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
|
||||
|
||||
`include "bc_r_pkt.vh"
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_BC_R_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_BC_W_TEST
|
||||
begin:EXCHG_DATA_BC_W_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_BC_W_TEST);
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
|
||||
|
||||
$fdisplay(spidata_file, "\n\n测试用例：广播写");
|
||||
`include "bc_w_pkt.vh"
|
||||
|
||||
`SPI_TRANS( (16'h0800), (`SPI_READ), (32), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h0800), (`SPI_READ), (32), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h0800), (`SPI_READ), (32), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h0800), (`SPI_READ), (32), (`IF_IDX(4)) );
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_BC_W_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_BC_RW_TEST
|
||||
begin:EXCHG_DATA_BC_RW_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_BC_RW_TEST);
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：广播读写");
|
||||
$display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
|
||||
|
||||
`include "bc_rw_pkt.vh"
|
||||
|
||||
`SPI_TRANS( (16'h0180), (`SPI_READ), (128), (`IF_IDX(1)) );
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_BC_RW_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
|
||||
`ifdef ENABLE_SYNC_TEST
|
||||
/*---------------------------------------------------------------------------------------------------------
|
||||
测试用例
|
||||
1. 测试 同步(sync) 和 同步输出 (sync_out)
|
||||
---------------------------------------------------------------------------------------------------------*/
|
||||
// 同步
|
||||
|
||||
begin:SYNC_TESTCASE0
|
||||
`BEGIN_TESTCASE(`ENABLE_SYNC_TEST);
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
|
||||
$display("sync @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
|
||||
$fdisplay(spidata_file, "\n\n测试用例：测试同步(sync)和同步输出(sync_out)");
|
||||
|
||||
//设置SM1在写入 0x18 len触发enq
|
||||
`include "sync_pkt.vh"
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_SYNC_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_SYNC_SIG0_TEST
|
||||
begin:SYNC_TESTCASE1
|
||||
`BEGIN_TESTCASE(`ENABLE_SYNC_SIG0_TEST);
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：测试同步信号(电平)");
|
||||
|
||||
`include "sync_sig_pkt.vh"
|
||||
|
||||
//`SPI_TRANS( (16'h0100), (`SPI_READ), (32), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(4)) );
|
||||
|
||||
|
||||
#100000
|
||||
//清脉冲
|
||||
txBuf[0+3] = 0; //负载0x122 sync0脉冲宽度
|
||||
txBuf[1+3] = 0; //负载0x123
|
||||
txBuf[2+3] = 0; //负载0x124 sync1脉冲宽度
|
||||
txBuf[3+3] = 0; //负载0x125
|
||||
txBuf[4+3] = 0; //负载0x126 sync2脉冲宽度
|
||||
txBuf[5+3] = 0; //负载0x127
|
||||
txBuf[6+3] = 0; //负载0x128 sync3脉冲宽度
|
||||
txBuf[7+3] = 0; //负载0x129
|
||||
`SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(1)) ); //slv2
|
||||
`SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(2)) ); //slv2
|
||||
`SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(3)) ); //slv2
|
||||
`SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(4)) ); //slv2
|
||||
|
||||
#100000
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_SYNC_SIG0_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_SYNC_SIG1_TEST
|
||||
begin:SYNC_TESTCASE2
|
||||
`BEGIN_TESTCASE(`ENABLE_SYNC_SIG1_TEST);
|
||||
_t_start = $realtime;
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：测试同步信号(脉冲)");
|
||||
|
||||
`include "sync_sig2_pkt.vh"
|
||||
|
||||
//`SPI_TRANS( (16'h0100), (`SPI_READ), (32), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(4)) );
|
||||
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_SYNC_SIG1_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`ifdef ENABLE_RESET_TEST
|
||||
begin:RESET_SYSTEM_TEST
|
||||
`BEGIN_TESTCASE(`ENABLE_RESET_TEST);
|
||||
$fdisplay(spidata_file, "\n\n测试用例：复位系统测试");
|
||||
txBuf[0+3] = 8'h0f;
|
||||
txBuf[1+3] = 8'h00;
|
||||
txBuf[2+3] = 8'h00;
|
||||
txBuf[3+3] = 8'h80;
|
||||
`SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(0)) );
|
||||
|
||||
|
||||
|
||||
#50000
|
||||
//复位系统
|
||||
$fdisplay(spidata_file, "-复位系统");
|
||||
txBuf[0+3] = 8'h01;
|
||||
txBuf[0+4] = 8'h00;
|
||||
txBuf[0+5] = 8'h66;
|
||||
txBuf[0+6] = 8'h79;
|
||||
`SPI_TRANS( (16'h40), (`SPI_WRITE), (4), (`IF_IDX(0)) );//复位主站
|
||||
`SPI_TRANS( (16'h40), (`SPI_WRITE), (4), (`IF_IDX(2)) );//复位从站2
|
||||
|
||||
|
||||
$fdisplay(spidata_file, "-配置系统");
|
||||
#50000
|
||||
txBuf[0+3] = 8'h01;
|
||||
`SPI_TRANS( (16'h00), (`SPI_WRITE), (1), (`IF_IDX(0)) );
|
||||
|
||||
txBuf[0+3] = 8'h02;
|
||||
`SPI_TRANS( (16'h00), (`SPI_WRITE), (1), (`IF_IDX(2)) );
|
||||
|
||||
#1000
|
||||
|
||||
$fdisplay(spidata_file, "\n广播读：使用SM2");
|
||||
$fdisplay(spidata_file, "-广播读");
|
||||
|
||||
`include "sm2_pkt.vh"
|
||||
|
||||
|
||||
$fdisplay(spidata_file, "-嗅探：使用SM0");
|
||||
$fdisplay(spidata_file, "-嗅探前，检查链路状态寄存器");
|
||||
//`SPI_TRANS( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-嗅探");
|
||||
//设置SM1在写入0x3地址触发enq
|
||||
|
||||
`include "detect_pkt.vh"
|
||||
|
||||
$fdisplay(spidata_file, "-嗅探后，检查链路状态寄存器");
|
||||
//`SPI_TRANS( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
|
||||
|
||||
$fdisplay(spidata_file, "-设置顺序地址前，检查顺序地址");
|
||||
//`SPI_TRANS( (16'h0010), (`SPI_READ), (5), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-设置顺序地址");
|
||||
`include "set_addr_pkt.vh"
|
||||
|
||||
//测试
|
||||
`SPI_TRANS( (16'hc0), (`SPI_READ), (6), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(4)) );
|
||||
|
||||
//读写
|
||||
#1000
|
||||
$fdisplay(spidata_file, "-设置顺序地址后，检查顺序地址");
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(4)) );
|
||||
|
||||
#1000
|
||||
|
||||
$fdisplay(spidata_file, "\n广播读：使用SM2");
|
||||
$fdisplay(spidata_file, "-广播读");
|
||||
|
||||
`include "sm2_pkt.vh"
|
||||
|
||||
|
||||
$fdisplay(spidata_file, "\n\n测试用例：测试同步(sync)和同步输出(sync_out)");
|
||||
|
||||
//设置SM1在写入 0x18 len触发enq
|
||||
`include "sync_pkt.vh"
|
||||
|
||||
/*
|
||||
#1000
|
||||
$fdisplay(spidata_file, "\n\n测试用例：测试同步信号(电平)");
|
||||
|
||||
`include "sync_sig_pkt.vh"
|
||||
|
||||
//`SPI_TRANS( (16'h0100), (`SPI_READ), (32), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(4)) );
|
||||
|
||||
#100000
|
||||
//清脉冲
|
||||
txBuf[0+3] = 0; //负载0x122 sync0脉冲宽度
|
||||
txBuf[1+3] = 0; //负载0x123
|
||||
txBuf[2+3] = 0; //负载0x124 sync1脉冲宽度
|
||||
txBuf[3+3] = 0; //负载0x125
|
||||
txBuf[4+3] = 0; //负载0x126 sync2脉冲宽度
|
||||
txBuf[5+3] = 0; //负载0x127
|
||||
txBuf[6+3] = 0; //负载0x128 sync3脉冲宽度
|
||||
txBuf[7+3] = 0; //负载0x129
|
||||
`SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(1)) ); //slv2
|
||||
`SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(2)) ); //slv2
|
||||
`SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(3)) ); //slv2
|
||||
`SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(4)) ); //slv2
|
||||
*/
|
||||
|
||||
`include "sync_sig3_pkt.vh"
|
||||
|
||||
//spi_trans( (16'h0100), (`SPI_READ), (32), (`IF_IDX(0)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(1)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(2)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(3)) );
|
||||
`SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(4)) );
|
||||
`END_TESTCASE(`ENABLE_RESET_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
`include "tc_runlist.vh"
|
||||
|
||||
#1000000
|
||||
|
||||
Reference in New Issue
Block a user