diff --git a/tb/shinTest/ShinTopSpiTb.v b/tb/shinTest/ShinTopSpiTb.v
index f8d2980..a977a33 100644
--- a/tb/shinTest/ShinTopSpiTb.v
+++ b/tb/shinTest/ShinTopSpiTb.v
@@ -754,64 +754,6 @@ initial begin
     end
   end
 
-`ifdef ENABLE_CODE____
-/*---------------------------------------------------------------------------------------------------------
-测试用例
-1. 设置IP为主站或从站，并读取设置结果，期望：0主，1~4从
----------------------------------------------------------------------------------------------------------*/
-  begin:SETTING_DEV_ROLE
-    //设置主站从站
-    $fdisplay(spidata_file, "\n\n测试用例：设置IP为主站或从站，并读取设置结果，期望：0主，1~4从");
-    txBuf[0+3] = 8'h01;
-    spi_trans( (16'h00), (`SPI_WRITE), (1), (`IF_IDX(0)) );
-
-    #1000
-    txBuf[0+3] = 8'h02;
-    spi_trans( (16'h0), (`SPI_WRITE), (1), (`IF_IDX(1)) );
-    
-    #1000
-    spi_trans( (16'h0), (`SPI_WRITE), (1), (`IF_IDX(2)) );
-    
-    #1000
-    spi_trans( (16'h0), (`SPI_WRITE), (1), (`IF_IDX(3)) );
-    
-    #1000
-    spi_trans( (16'h0), (`SPI_WRITE), (1), (`IF_IDX(4)) );
-
-    $fdisplay(spidata_file, "-设置完毕，检查接口寄存器");
-    spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(0)) );
-    spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(1)) );
-    spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(2)) );
-    spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(3)) );
-    spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(4)) );
-    /*
-    $display("------------------------------ start! %t", $realtime);
-    _reset_deadline_ind = 1;
-    @(posedge _deadline_ind) #5 begin end
-    $display("------------------------------ End! %t", $realtime);
-    */
-  end
-`endif
-
-`ifdef ENABLE_ENCRYPTION
-  begin:ENABLE_ENCRYPTION_TESTCASE
-
-    $fdisplay(spidata_file, "\n\n测试用例：加密");
-    `SETTING_ENCRYPTION;
-    spi_trans( (16'h50), (`SPI_WRITE), (17), (`IF_IDX(0)) );
-    spi_trans( (16'h50), (`SPI_WRITE), (17), (`IF_IDX(1)) );
-    spi_trans( (16'h50), (`SPI_WRITE), (17), (`IF_IDX(2)) );
-    spi_trans( (16'h50), (`SPI_WRITE), (17), (`IF_IDX(3)) );
-    spi_trans( (16'h50), (`SPI_WRITE), (17), (`IF_IDX(4)) );
-
-    spi_trans( (16'h50), (`SPI_READ), (17), (`IF_IDX(0)) );
-    spi_trans( (16'h50), (`SPI_READ), (17), (`IF_IDX(1)) );
-    spi_trans( (16'h50), (`SPI_READ), (17), (`IF_IDX(2)) );
-    spi_trans( (16'h50), (`SPI_READ), (17), (`IF_IDX(3)) );
-    spi_trans( (16'h50), (`SPI_READ), (17), (`IF_IDX(4)) );
-  end
-`endif
-
 `ifdef ENABLE_INT_INIT_TEST
   begin:CHECK_INTERRUPT_SIG
     $fdisplay(spidata_file, "\n\n测试用例：检查设备的INTERRUPT信号");
@@ -919,720 +861,6 @@ initial begin
   end
 `endif
 
-`ifdef ENABLE_DET1_TEST
-/*---------------------------------------------------------------------------------------------------------
-测试用例3
----------------------------------------------------------------------------------------------------------*/
-  //嗅探
-  begin:DETECT_DEV_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_DET1_TEST);
-    _t_start = $realtime;
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：发送嗅探包，需要在波形文件里检查");
-  
-    $fdisplay(spidata_file, "-嗅探前，检查链路状态寄存器");
-    //spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
-
-    $fdisplay(spidata_file, "-嗅探");
-
-    `include "detect_pkt.vh"
-    
-    // 顺序索引
-    //#50000
-    #1000
-    $fdisplay(spidata_file, "-嗅探后，检查链路状态寄存器");
-    //spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_DET1_TEST);
-  end
-`endif
-
-`ifdef ENABLE_SET_ADDR_TEST
-/*---------------------------------------------------------------------------------------------------------
-测试用例
----------------------------------------------------------------------------------------------------------*/
-  begin:SET_ADDR_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_SET_ADDR_TEST);
-    _t_start = $realtime;
-    $fdisplay(spidata_file, "\n\n测试用例：设置顺序索引");
-    $display("index @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
-
-    $fdisplay(spidata_file, "-设置顺序地址前，检查顺序地址");
-    //spi_trans( (16'h0010), (`SPI_READ), (5), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(4)) );
-
-    $fdisplay(spidata_file, "-设置顺序地址");
-    `include "set_addr_pkt.vh"
-
-    //测试
-    `SPI_TRANS( (16'hc0), (`SPI_READ), (6), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(4)) );
-
-    //读写
-    #1000
-    $fdisplay(spidata_file, "-设置顺序地址后，检查顺序地址");
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(4)) );
-
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_SET_ADDR_TEST);
-  end
-`endif
-
-`ifdef ENABLE_DET2_TEST
-/*---------------------------------------------------------------------------------------------------------
-测试用例
----------------------------------------------------------------------------------------------------------*/
-  begin:DETECT_DEV_TESTCASE_2
-    `BEGIN_TESTCASE(`ENABLE_DET2_TEST);
-    //嗅探
-    _t_start = $realtime;
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：发送嗅探包，需要在波形文件里检查");
-
-    $fdisplay(spidata_file, "嗅探：使用SM0");
-    $fdisplay(spidata_file, "-嗅探前，检查链路状态寄存器");
-    //`SPI_TRANS( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
-
-    $fdisplay(spidata_file, "-嗅探");
-    //设置SM1在写入0x3地址触发enq
-    
-    `include "detect_pkt2.vh"
-
-    $fdisplay(spidata_file, "-嗅探后，检查链路状态寄存器");
-    //`SPI_TRANS( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_DET2_TEST);
-  end
-`endif
-
-`ifdef ENABLE_DET_ERR1_TEST
-  begin:DET_ERR_TEST
-    `BEGIN_TESTCASE(`ENABLE_DET_ERR1_TEST);
-    //嗅探
-    _t_start = $realtime;
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：发送错误嗅探包");
-
-    `include "detect_err_pkt.vh"
-
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-
-    $fdisplay(spidata_file, "-检查中断");
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
-
-
-    $fdisplay(spidata_file, "-清除中断");
-    txBuf[3] = 8'h00;
-    txBuf[4] = 8'h00;
-    txBuf[5] = 8'h00;
-    txBuf[6] = 8'h60;
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(4)) );
-
-    $fdisplay(spidata_file, "-再次检查中断");
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
-    `END_TESTCASE(`ENABLE_DET_ERR1_TEST);
-  end
-`endif
-
-`ifdef ENABLE_SMx_SEND1_TEST
-  begin:SM1_SEND_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_SMx_SEND1_TEST);
-    _t_start = $realtime;
-    $fdisplay(spidata_file, "\n单读：使用SM1");
-    $fdisplay(spidata_file, "-SM1：数据包");
-
-    `include "sm1_pkt.vh"
-
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_SMx_SEND1_TEST);
-  end
-  
-`endif
-
-`ifdef ENABLE_SMx_SEND2_TEST
-  
-  begin:SM2_SEND_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_SMx_SEND2_TEST);
-    _t_start = $realtime;
-    #1000
-    $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
-
-    $fdisplay(spidata_file, "\n广播读：使用SM2");
-    $fdisplay(spidata_file, "-广播读");
-
-    `include "sm2_pkt.vh"
-
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_SMx_SEND2_TEST);
-  end
-`endif
-
-`ifdef ENABLE_SMx_SEND3_TEST  
-  begin:SM3_SEND_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_SMx_SEND3_TEST);
-    _t_start = $realtime;
-    #1000
-    $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
-    $fdisplay(spidata_file, "\n广播写：使用SM3");
-    $fdisplay(spidata_file, "-SM3广播写");
-
-    `include "sm3_pkt.vh"
-
-    `SPI_TRANS( (16'h0800), (`SPI_READ), (16), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h0800), (`SPI_READ), (16), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h0800), (`SPI_READ), (16), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h0800), (`SPI_READ), (16), (`IF_IDX(4)) );
-
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_SMx_SEND3_TEST);
-  end
-`endif
-
-
-`ifdef ENABLE_ERR_PKT1_TEST
-  begin:ERR_PKT1_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_ERR_PKT1_TEST);
-    //嗅探
-    _t_start = $realtime;
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：发送错误数据包1");
-
-    `include "err_pkt1.vh"
-
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-
-    $fdisplay(spidata_file, "-检查中断");
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
-
-
-    $fdisplay(spidata_file, "-清除中断");
-    txBuf[3] = 8'h00;
-    txBuf[4] = 8'h00;
-    txBuf[5] = 8'h00;
-    txBuf[6] = 8'h60;
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(4)) );
-
-    $fdisplay(spidata_file, "-再次检查中断");
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
-    `END_TESTCASE(`ENABLE_ERR_PKT1_TEST);
-  end
-`endif
-
-`ifdef ENABLE_ERR_PKT2_TEST
-  begin:ERR_PKT2_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_ERR_PKT2_TEST);
-    //嗅探
-    _t_start = $realtime;
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：发送错误数据包2");
-
-    `include "err_pkt2.vh"
-
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-
-    $fdisplay(spidata_file, "-检查中断");
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
-
-
-    $fdisplay(spidata_file, "-清除中断");
-    txBuf[3] = 8'h00;
-    txBuf[4] = 8'h00;
-    txBuf[5] = 8'h00;
-    txBuf[6] = 8'h60;
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(4)) );
-
-    $fdisplay(spidata_file, "-再次检查中断");
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
-    `END_TESTCASE(`ENABLE_ERR_PKT2_TEST);
-  end
-`endif
-
-`ifdef ENABLE_ERR_PKT3_TEST
-  begin:ERR_PKT3_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_ERR_PKT3_TEST);
-    //嗅探
-    _t_start = $realtime;
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：发送错误数据包3");
-
-    `include "err_pkt3.vh"
-
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-
-    $fdisplay(spidata_file, "-检查中断");
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
-
-
-    $fdisplay(spidata_file, "-清除中断");
-    txBuf[3] = 8'h00;
-    txBuf[4] = 8'h00;
-    txBuf[5] = 8'h00;
-    txBuf[6] = 8'h60;
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(4)) );
-
-    $fdisplay(spidata_file, "-再次检查中断");
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h74), (`SPI_READ), (4), (`IF_IDX(4)) );
-    `END_TESTCASE(`ENABLE_ERR_PKT3_TEST);
-  end
-`endif
-
-
-/*---------------------------------------------------------------------------------------------------------
-测试用例
-1. 交换数据sm0~sm7
-2. 交换数据sm0~sm7
-3. 交换数据sm0~sm7(中断、状态)
-4. 交换数据sm0~sm7(R/W/RW, BR/BW/BRW)
-4. 寄存器单读/写/读写，寄存器广播读/写/读写
-5. 以上交换数据的错误形式
----------------------------------------------------------------------------------------------------------*/  
-`ifdef ENABLE_EXCHG_DATA_SEQ0_TEST
-  begin:EXCHG_DATA_SEQ0_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_EXCHG_DATA_SEQ0_TEST);
-    _t_start = $realtime;
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：交换数据sm0~sm7");
-    $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
-    
-    `include "seq_0_pkt.vh"
-
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_EXCHG_DATA_SEQ0_TEST);
-  end
-`endif
-
-`ifdef ENABLE_EXCHG_DATA_SEQ1_TEST
-  begin:EXCHG_DATA_SEQ1_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_EXCHG_DATA_SEQ1_TEST);
-    _t_start = $realtime;
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：交换数据写dev2_sm0/dev1_sm2/dev3_sm4/dev4_sm6");
-    $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
-
-    `include "seq_1_pkt.vh"
-
-    `SPI_TRANS( (16'h1800), (`SPI_READ), (64), (`IF_IDX(1)) );
-    $fdisplay(spidata_file, "-嗅探前，检查链路状态寄存器");
-    //`SPI_TRANS( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
-
-    $fdisplay(spidata_file, "-嗅探");
-    //设置SM1在写入0x3地址触发enq
-    
-    `include "detect_pkt.vh"
-
-    $fdisplay(spidata_file, "-嗅探后，检查链路状态寄存器");
-    //`SPI_TRANS( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );  
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
-    `SPI_TRANS( (16'h0800), (`SPI_READ), (64), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h2800), (`SPI_READ), (64), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h3800), (`SPI_READ), (64), (`IF_IDX(4)) );
-    
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_EXCHG_DATA_SEQ1_TEST);
-  end
-`endif
-
-`ifdef ENABLE_EXCHG_DATA_SEQ2_TEST
-  begin:EXCHG_DATA_SEQ2_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_EXCHG_DATA_SEQ2_TEST);
-    _t_start = $realtime;
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：交换数据读dev1_sm1/dev2_sm3/dev3_sm5/dev4_sm7");
-    $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
-
-    `include "seq_2_pkt.vh"
-
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_EXCHG_DATA_SEQ2_TEST);
-  end
-`endif
-
-`ifdef ENABLE_EXCHG_DATA_SEQ3_TEST
-  begin:EXCHG_DATA_SEQ3_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_EXCHG_DATA_SEQ3_TEST);
-    _t_start = $realtime;
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：交换数据读写");
-    $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
-
-    `include "seq_3_pkt.vh"
-
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_EXCHG_DATA_SEQ3_TEST);
-  end
-`endif
-
-`ifdef ENABLE_BC_R_TEST
-  
-  begin:EXCHG_DATA_BC_R_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_BC_R_TEST);
-    _t_start = $realtime;
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：广播读");
-    $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
-    
-    `include "bc_r_pkt.vh"
-    
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_BC_R_TEST);
-  end
-`endif
-
-`ifdef ENABLE_BC_W_TEST
-  begin:EXCHG_DATA_BC_W_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_BC_W_TEST);
-    _t_start = $realtime;
-    #1000
-    $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
-
-    $fdisplay(spidata_file, "\n\n测试用例：广播写");
-    `include "bc_w_pkt.vh"
-
-    `SPI_TRANS( (16'h0800), (`SPI_READ), (32), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h0800), (`SPI_READ), (32), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h0800), (`SPI_READ), (32), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h0800), (`SPI_READ), (32), (`IF_IDX(4)) );
-    
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_BC_W_TEST);
-  end
-`endif
-
-`ifdef ENABLE_BC_RW_TEST
-  begin:EXCHG_DATA_BC_RW_TESTCASE
-    `BEGIN_TESTCASE(`ENABLE_BC_RW_TEST);
-    _t_start = $realtime;
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：广播读写");
-    $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
-
-    `include "bc_rw_pkt.vh"
-
-    `SPI_TRANS( (16'h0180), (`SPI_READ), (128), (`IF_IDX(1)) );
-    
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_BC_RW_TEST);
-  end
-`endif
-
-
-`ifdef ENABLE_SYNC_TEST
-/*---------------------------------------------------------------------------------------------------------
-测试用例
-1. 测试 同步(sync) 和 同步输出 (sync_out)
----------------------------------------------------------------------------------------------------------*/
-  // 同步
-
-  begin:SYNC_TESTCASE0
-    `BEGIN_TESTCASE(`ENABLE_SYNC_TEST);
-    _t_start = $realtime;
-    #1000
-
-    $display("sync @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
-    $fdisplay(spidata_file, "\n\n测试用例：测试同步(sync)和同步输出(sync_out)");
-
-    //设置SM1在写入 0x18 len触发enq
-    `include "sync_pkt.vh"
-
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_SYNC_TEST);
-  end
-`endif
-
-`ifdef ENABLE_SYNC_SIG0_TEST 
-  begin:SYNC_TESTCASE1
-    `BEGIN_TESTCASE(`ENABLE_SYNC_SIG0_TEST);
-    _t_start = $realtime;
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：测试同步信号(电平)");
-
-    `include "sync_sig_pkt.vh"
-
-    //`SPI_TRANS( (16'h0100), (`SPI_READ), (32), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(4)) );
-
-  
-  #100000
-    //清脉冲
-    txBuf[0+3] = 0;  //负载0x122 sync0脉冲宽度
-    txBuf[1+3] = 0;  //负载0x123
-    txBuf[2+3] = 0;  //负载0x124 sync1脉冲宽度
-    txBuf[3+3] = 0;  //负载0x125
-    txBuf[4+3] = 0;  //负载0x126 sync2脉冲宽度
-    txBuf[5+3] = 0;  //负载0x127 
-    txBuf[6+3] = 0;  //负载0x128 sync3脉冲宽度
-    txBuf[7+3] = 0;  //负载0x129
-    `SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(1)) ); //slv2
-    `SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(2)) ); //slv2
-    `SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(3)) ); //slv2
-    `SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(4)) ); //slv2
-
-  #100000
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_SYNC_SIG0_TEST);
-  end
-`endif
-
-`ifdef ENABLE_SYNC_SIG1_TEST
-  begin:SYNC_TESTCASE2
-    `BEGIN_TESTCASE(`ENABLE_SYNC_SIG1_TEST);
-    _t_start = $realtime;
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：测试同步信号(脉冲)");
-
-    `include "sync_sig2_pkt.vh"
-
-    //`SPI_TRANS( (16'h0100), (`SPI_READ), (32), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(4)) );
-
-    _t_end = $realtime;
-    $fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
-    `END_TESTCASE(`ENABLE_SYNC_SIG1_TEST);
-  end
-`endif
-  
-`ifdef ENABLE_RESET_TEST
-  begin:RESET_SYSTEM_TEST
-    `BEGIN_TESTCASE(`ENABLE_RESET_TEST);
-    $fdisplay(spidata_file, "\n\n测试用例：复位系统测试");
-    txBuf[0+3] = 8'h0f;
-    txBuf[1+3] = 8'h00;
-    txBuf[2+3] = 8'h00;
-    txBuf[3+3] = 8'h80;
-    `SPI_TRANS( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(0)) );
-
-
-
-    #50000
-    //复位系统
-    $fdisplay(spidata_file, "-复位系统");
-    txBuf[0+3] = 8'h01;
-    txBuf[0+4] = 8'h00;
-    txBuf[0+5] = 8'h66;
-    txBuf[0+6] = 8'h79;
-    `SPI_TRANS( (16'h40), (`SPI_WRITE), (4), (`IF_IDX(0)) );//复位主站
-    `SPI_TRANS( (16'h40), (`SPI_WRITE), (4), (`IF_IDX(2)) );//复位从站2
-
-
-    $fdisplay(spidata_file, "-配置系统");    
-    #50000
-    txBuf[0+3] = 8'h01;
-    `SPI_TRANS( (16'h00), (`SPI_WRITE), (1), (`IF_IDX(0)) );
-
-    txBuf[0+3] = 8'h02;
-    `SPI_TRANS( (16'h00), (`SPI_WRITE), (1), (`IF_IDX(2)) );
-
-    #1000
-
-    $fdisplay(spidata_file, "\n广播读：使用SM2");
-    $fdisplay(spidata_file, "-广播读");
-
-    `include "sm2_pkt.vh"
-
-
-    $fdisplay(spidata_file, "-嗅探：使用SM0");
-    $fdisplay(spidata_file, "-嗅探前，检查链路状态寄存器");
-    //`SPI_TRANS( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
-
-    $fdisplay(spidata_file, "-嗅探");
-    //设置SM1在写入0x3地址触发enq
-    
-    `include "detect_pkt.vh"
-
-    $fdisplay(spidata_file, "-嗅探后，检查链路状态寄存器");
-    //`SPI_TRANS( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
-
-
-    $fdisplay(spidata_file, "-设置顺序地址前，检查顺序地址");
-    //`SPI_TRANS( (16'h0010), (`SPI_READ), (5), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(4)) );
-
-    $fdisplay(spidata_file, "-设置顺序地址");
-    `include "set_addr_pkt.vh"
-
-    //测试
-    `SPI_TRANS( (16'hc0), (`SPI_READ), (6), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h0a), (`SPI_READ), (2), (`IF_IDX(4)) );
-
-    //读写
-    #1000
-    $fdisplay(spidata_file, "-设置顺序地址后，检查顺序地址");
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h0000), (`SPI_READ), (16), (`IF_IDX(4)) );
-
-    #1000
-
-    $fdisplay(spidata_file, "\n广播读：使用SM2");
-    $fdisplay(spidata_file, "-广播读");
-
-    `include "sm2_pkt.vh"
-
-    
-    $fdisplay(spidata_file, "\n\n测试用例：测试同步(sync)和同步输出(sync_out)");
-
-    //设置SM1在写入 0x18 len触发enq
-    `include "sync_pkt.vh"
-
-    /*
-    #1000
-    $fdisplay(spidata_file, "\n\n测试用例：测试同步信号(电平)");
-
-    `include "sync_sig_pkt.vh"
-
-    //`SPI_TRANS( (16'h0100), (`SPI_READ), (32), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(4)) );
-
-  #100000
-    //清脉冲
-    txBuf[0+3] = 0;  //负载0x122 sync0脉冲宽度
-    txBuf[1+3] = 0;  //负载0x123
-    txBuf[2+3] = 0;  //负载0x124 sync1脉冲宽度
-    txBuf[3+3] = 0;  //负载0x125
-    txBuf[4+3] = 0;  //负载0x126 sync2脉冲宽度
-    txBuf[5+3] = 0;  //负载0x127 
-    txBuf[6+3] = 0;  //负载0x128 sync3脉冲宽度
-    txBuf[7+3] = 0;  //负载0x129
-    `SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(1)) ); //slv2
-    `SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(2)) ); //slv2
-    `SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(3)) ); //slv2
-    `SPI_TRANS( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(4)) ); //slv2
-    */
-    
-    `include "sync_sig3_pkt.vh"
-
-    //spi_trans( (16'h0100), (`SPI_READ), (32), (`IF_IDX(0)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(1)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(2)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(3)) );
-    `SPI_TRANS( (16'h0100), (`SPI_READ), (16'h48), (`IF_IDX(4)) );
-    `END_TESTCASE(`ENABLE_RESET_TEST);
-  end
-`endif
-
   `include "tc_runlist.vh"
 
   #1000000
diff --git a/tb/shinTest/gen_pkt.py b/tb/shinTest/gen_pkt.py
index f8f6293..84e1871 100755
--- a/tb/shinTest/gen_pkt.py
+++ b/tb/shinTest/gen_pkt.py
@@ -6,8 +6,8 @@ from testcase import environment, readregs, ebmmu, detect, errorPkt, watchdog, b
 if __name__ == '__main__':
     environment.bringup()
 
-    detect.tc1()
-    detect.tc2()
+    #detect.tc1()
+    #detect.tc2()
 
     #add_tc_2_runlist(errorPkt.tc1())
     #add_tc_2_runlist(errorPkt.tc2())
diff --git a/tb/shinTest/testcase/environment.py b/tb/shinTest/testcase/environment.py
index f51c975..f4f0fe8 100644
--- a/tb/shinTest/testcase/environment.py
+++ b/tb/shinTest/testcase/environment.py
@@ -86,15 +86,54 @@ def bringup():
     
     genPkt.addBeforeExc(genMessageCode("--设置环境，进行第二次嗅探"))
 
+    int_data=[0x00, 0x00]
+    clear_int = [0xff, 0xff, 0xff, 0xff]
     genPkt.addAfterExc(genWriteTransLenCode(gen_file_def_ap, sm_idx)
                        +genWriteTransPktCode(gen_file_def_ap, sm_idx)
                        +genTrgTransPktCode(gen_file_def_ap, sm_idx)
                        +genReadAckPktCode(gen_file_def_ap, sm_idx)
+                       
                        +genMessageCode("--嗅探后检查链路状态寄存器")
                        +genIFRwDataCode(1, 0xc0, False, 4)
                        +genIFRwDataCode(2, 0xc0, False, 4)
                        +genIFRwDataCode(3, 0xc0, False, 4)
                        +genIFRwDataCode(4, 0xc0, False, 4)
+                       
+                       +genMessageCode("--设置中断为脉冲模式")
+                       +genIFRwDataCode(0, 0x7c, True, 2, int_data)
+                       +genIFRwDataCode(1, 0x7c, True, 2, int_data)
+                       +genIFRwDataCode(2, 0x7c, True, 2, int_data)
+                       +genIFRwDataCode(3, 0x7c, True, 2, int_data)
+                       +genIFRwDataCode(4, 0x7c, True, 2, int_data)
+                       
+                       +genMessageCode("--清除中断")
+                       +genIFRwDataCode(0, 0x78, True, 4, clear_int)
+                       +genIFRwDataCode(1, 0x78, True, 4, clear_int)
+                       +genIFRwDataCode(2, 0x78, True, 4, clear_int)
+                       +genIFRwDataCode(3, 0x78, True, 4, clear_int)
+                       +genIFRwDataCode(4, 0x78, True, 4, clear_int)
+                       
+                       +genMessageCode("--读取中断状态")
+                       +genIFRwDataCode(0, 0x74, False, 4)
+                       +genIFRwDataCode(1, 0x74, False, 4)
+                       +genIFRwDataCode(2, 0x74, False, 4)
+                       +genIFRwDataCode(3, 0x74, False, 4)
+                       +genIFRwDataCode(4, 0x74, False, 4)
+                       
+                       +genMessageCode("--清除中断")
+                       +genIFRwDataCode(0, 0x78, True, 4, clear_int)
+                       +genIFRwDataCode(1, 0x78, True, 4, clear_int)
+                       +genIFRwDataCode(2, 0x78, True, 4, clear_int)
+                       +genIFRwDataCode(3, 0x78, True, 4, clear_int)
+                       +genIFRwDataCode(4, 0x78, True, 4, clear_int)
+                       
+                       +genMessageCode("--读取中断状态")
+                       +genIFRwDataCode(0, 0x74, False, 4)
+                       +genIFRwDataCode(1, 0x74, False, 4)
+                       +genIFRwDataCode(2, 0x74, False, 4)
+                       +genIFRwDataCode(3, 0x74, False, 4)
+                       +genIFRwDataCode(4, 0x74, False, 4)
+                       
                        +genTcEndFrameCode(gen_file_def)
                        )
     genPkt.gen("./generated/shin/%s.vh"%(gen_file_def, ), 1, True, gen_file_def_ap)