eb001/tb/shinTest/ShinTopSpiTb.v

`timescale 1 ns / 1 ps


module ShinTopSpiTb(

);

    reg clock;
    reg reset;
    reg clk8x;

    wire [3:0] dDat_w;
    wire [3:0] uDat_w;

    wire spi_sck;
    wire spi_mosi;
    wire [4:0] spi_miso;
    reg [14:0] spi_csn;

    wire qspi_sck;
    wire [3:0] qspi_mosi;
    wire [40-1:0] qspi_miso;

    wire isResp;

    integer spidata_file;
    integer c_line;

ShinTop s_ShinTop_Mst(
  .clock(clock),
  .reset(reset),

  .io_clk8x(clk8x),
  .io_dDatIn(1'b0),
  .io_dDatOut(dDat_w[0]),
  .io_uDatIn(uDat_w[0]),
  .io_uDatOut(),
  
  .io_iqspi_sck(qspi_sck),
  .io_iqspi_mosi(qspi_mosi),
  .io_iqspi_miso(qspi_miso[3:0]),
  .io_iqspi_isDirIn(),
  .io_iqspi_csn(spi_csn[0]),

  .io_ospi_sck (spi_sck),
  .io_ospi_mosi(spi_mosi),
  .io_ospi_miso(spi_miso[0]),
  .io_ospi_csn (spi_csn[5]),


  .io_oqspi_sck(qspi_sck),
  .io_oqspi_mosi(qspi_mosi),
  .io_oqspi_miso(qspi_miso[4*5+3:4*5]),
  .io_oqspi_isDirIn(),
  .io_oqspi_csn(spi_csn[10]),

  .io_rsp_valid(isResp),
  .io_rsp_bits_isError(),
  .io_rsp_bits_length()
);

ShinTop s_ShinTop_slv0(
  .clock(clock),
  .reset(reset),

  .io_clk8x(clk8x),
  .io_dDatIn(dDat_w[0]),
  .io_dDatOut(dDat_w[1]),
  .io_uDatIn(uDat_w[1]),
  .io_uDatOut(uDat_w[0]),
  
  .io_iqspi_sck(qspi_sck),
  .io_iqspi_mosi(qspi_mosi),
  .io_iqspi_miso(qspi_miso[4*1+3:4*1]),
  .io_iqspi_isDirIn(),
  .io_iqspi_csn(spi_csn[1]),

  .io_ospi_sck (spi_sck),
  .io_ospi_mosi(spi_mosi),
  .io_ospi_miso(spi_miso[1]),
  .io_ospi_csn (spi_csn[6]),

  .io_oqspi_sck(qspi_sck),
  .io_oqspi_mosi(qspi_mosi),
  .io_oqspi_miso(qspi_miso[4*6+3:4*6]),
  .io_oqspi_isDirIn(),
  .io_oqspi_csn(spi_csn[11]),

  .io_rsp_valid(),
  .io_rsp_bits_isError(),
  .io_rsp_bits_length()
);

ShinTop s_ShinTop_slv1(
  .clock(clock),
  .reset(reset),

  .io_clk8x(clk8x),
  .io_dDatIn(dDat_w[1]),
  .io_dDatOut(dDat_w[2]),
  .io_uDatIn(uDat_w[2]),
  .io_uDatOut(uDat_w[1]),
  
  .io_iqspi_sck(qspi_sck),
  .io_iqspi_mosi(qspi_mosi),
  .io_iqspi_miso(qspi_miso[4*2+3:4*2]),
  .io_iqspi_isDirIn(),
  .io_iqspi_csn(spi_csn[2]),

  .io_ospi_sck (spi_sck),
  .io_ospi_mosi(spi_mosi),
  .io_ospi_miso(spi_miso[2]),
  .io_ospi_csn (spi_csn[7]),

  .io_oqspi_sck(qspi_sck),
  .io_oqspi_mosi(qspi_mosi),
  .io_oqspi_miso(qspi_miso[4*7+3:4*7]),
  .io_oqspi_isDirIn(),
  .io_oqspi_csn(spi_csn[12]),

  .io_rsp_valid(),
  .io_rsp_bits_isError(),
  .io_rsp_bits_length()
);

ShinTop s_ShinTop_slv2(
  .clock(clock),
  .reset(reset),

  .io_clk8x(clk8x),
  .io_dDatIn(dDat_w[2]),
  .io_dDatOut(dDat_w[3]),
  .io_uDatIn(uDat_w[3]),
  .io_uDatOut(uDat_w[2]),
  
  .io_iqspi_sck(qspi_sck),
  .io_iqspi_mosi(qspi_mosi),
  .io_iqspi_miso(qspi_miso[4*3+3:4*3]),
  .io_iqspi_isDirIn(),
  .io_iqspi_csn(spi_csn[3]),

  .io_ospi_sck (spi_sck),
  .io_ospi_mosi(spi_mosi),
  .io_ospi_miso(spi_miso[3]),
  .io_ospi_csn (spi_csn[8]),

  .io_oqspi_sck(qspi_sck),
  .io_oqspi_mosi(qspi_mosi),
  .io_oqspi_miso(qspi_miso[4*8+3:4*8]),
  .io_oqspi_isDirIn(),
  .io_oqspi_csn(spi_csn[13]),

  .io_rsp_valid(),
  .io_rsp_bits_isError(),
  .io_rsp_bits_length()
);

ShinTop s_ShinTop_slv3(
  .clock(clock),
  .reset(reset),

  .io_clk8x(clk8x),
  .io_dDatIn(dDat_w[3]),
  .io_dDatOut(),
  .io_uDatIn(1'b0),
  .io_uDatOut(uDat_w[3]),

  .io_iqspi_sck(qspi_sck),
  .io_iqspi_mosi(qspi_mosi),
  .io_iqspi_miso(qspi_miso[4*4+3:4*4]),
  .io_iqspi_isDirIn(),
  .io_iqspi_csn(spi_csn[4]),

  .io_ospi_sck (spi_sck),
  .io_ospi_mosi(spi_mosi),
  .io_ospi_miso(spi_miso[4]),
  .io_ospi_csn (spi_csn[9]),

  .io_oqspi_sck(qspi_sck),
  .io_oqspi_mosi(qspi_mosi),
  .io_oqspi_miso(qspi_miso[4*9+3:4*9]),
  .io_oqspi_isDirIn(),
  .io_oqspi_csn(spi_csn[14]),

  .io_rsp_valid(),
  .io_rsp_bits_isError(),
  .io_rsp_bits_length()
);









initial begin
	clock = 0;
  clk8x = 0;
	reset = 0;

  spi_csn  = ~15'b0;

	#100
	reset <= 1;

	#240
	reset <= 0;

#10000000
	$display("Time Out !!!");
  	$fclose(spidata_file);
	$stop;
end

initial begin
	forever begin #20 clk8x <= ~clk8x; end
end

initial begin
	forever begin #80 clock <= ~clock; end
end

initial
begin
  	spidata_file = $fopen("spi_trans_data.txt", "w");
  	if (!spidata_file) $display("文件打开失败");
	$dumpfile("./tb/build/wave.vcd"); //生成的vcd文件名称
	$dumpvars(0, ShinTopSpiTb);//tb模块名称
end























  `define SCKFRE #640

  reg sck = 0;
  
  initial begin
      forever begin 
        `SCKFRE sck <= ~sck;
      end
  end

  assign spi_sck  = sck;
  assign qspi_sck = sck;


  reg [7:0] txBuf[0:2047];
  reg [7:0] rxBuf[0:2047];
  reg [7:0] exChangeReg;



  assign spi_mosi = exChangeReg[7];
  assign qspi_mosi = exChangeReg[7:4];
  wire [3:0] qspi_mux_miso = 
    ( qspi_miso[4*0+3:4*0] & ~{4{spi_csn[ 0]}}) |
    ( qspi_miso[4*1+3:4*1] & ~{4{spi_csn[ 1]}}) |
    ( qspi_miso[4*2+3:4*2] & ~{4{spi_csn[ 2]}}) |
    ( qspi_miso[4*3+3:4*3] & ~{4{spi_csn[ 3]}}) |
    ( qspi_miso[4*4+3:4*4] & ~{4{spi_csn[ 4]}}) |
    ( qspi_miso[4*5+3:4*5] & ~{4{spi_csn[10]}}) |
    ( qspi_miso[4*6+3:4*6] & ~{4{spi_csn[11]}}) |
    ( qspi_miso[4*7+3:4*7] & ~{4{spi_csn[12]}}) |
    ( qspi_miso[4*8+3:4*8] & ~{4{spi_csn[13]}}) |
    ( qspi_miso[4*9+3:4*9] & ~{4{spi_csn[14]}});

  wire spi_mux_miso = 
    ( spi_miso[0] & ~spi_csn[5] ) |
    ( spi_miso[1] & ~spi_csn[6] ) |
    ( spi_miso[2] & ~spi_csn[7] ) |
    ( spi_miso[3] & ~spi_csn[8] ) |
    ( spi_miso[4] & ~spi_csn[9] );

  reg isReq = 0;
  reg isBusy = 0;

  reg [11:0] length;
  reg [7:0] idx;

  reg [11:0] transCnt;
  reg [11:0] byteCnt;
  reg [2:0] bitCnt;


always @(posedge clock) begin
  if( isReq & sck == 0 ) begin
    isBusy   <= #5 1'b1;
    transCnt <= #5 0;

    byteCnt <= #5 ~12'b0;
    bitCnt  <= #5 ~3'b0;

    spi_csn[idx] <= #5 1'b0;
    exChangeReg <= txBuf[0];
  end
end


wire isQspi = (idx >= 0 && idx <= 4) || idx >= 10;
wire [11:0] nextByteCnt = byteCnt + 1;

always @(posedge sck) begin
  if( isBusy ) begin
    if( transCnt <= length ) begin
      if( isQspi ) begin
        bitCnt <= ~bitCnt;
      end else begin
        bitCnt <= bitCnt + 1;
      end
      
      if( &bitCnt ) begin
        byteCnt <= byteCnt +1;
        transCnt <= transCnt + 1;
        rxBuf[byteCnt] <= isQspi ? {exChangeReg[3:0], qspi_mux_miso} : {exChangeReg[6:0], spi_mux_miso};
        if( txBuf[2] === 1 & nextByteCnt >= 4) begin
          $display("spi read out @ %x", exChangeReg);
        end
        if( txBuf[2] === 1 & nextByteCnt >= 3) begin
          exChangeReg <= isQspi ? {exChangeReg[3:0], qspi_mux_miso} : {exChangeReg[6:0], spi_mux_miso};
        end else begin
          exChangeReg <= txBuf[nextByteCnt];
        end
      end else begin
        if( isQspi ) begin
          exChangeReg <= {exChangeReg[3:0], qspi_mux_miso};
        end else begin
          exChangeReg <= {exChangeReg[6:0], spi_mux_miso};
        end

      end
    end else begin
      isBusy       <= #5 1'b0;
      spi_csn[idx] <= #5 1'b1;
    end
  end
end




//mst slv0~slv3的 内部qspi调用即设置
//sidx为0~4；外部spi为5~9，外部qspi为10~15
task spi_trans( input [15:0] saddress, input [7:0] scmd, input [12:0] slength,input [7:0] sidx );
  begin
    txBuf[0] <= saddress[7:0];
    txBuf[1] <= saddress[15:8];
    txBuf[2] <= scmd;

    length <= slength + 3;
    idx <= sidx;

    #5
    @(negedge sck)
    isReq <= 1;
    @(posedge sck) #5
    isReq <= 0;

    @( negedge isBusy) #1000
    begin 
      //$fwrite(spidata_file, "------------%5t------------\n", $time);
      $fwrite(spidata_file, "T:%2tns \tdev:%4d, addr:0x%02h%02h, %s, len:%4d\n", 
          $time/1000, sidx, txBuf[1], txBuf[0], 
          ((txBuf[2] == 0)? "Write":" Read"), slength);
      if (scmd == 0) begin
        for (integer i=0; i<slength; i++) begin
          $fwrite(spidata_file, "%02h ", txBuf[i + 3]); 
          c_line = 0;
          if ((i+1)%16 == 0) begin
            $fwrite(spidata_file, "\n");
            c_line = 1;
          end
        end
      end else begin
        for (integer i=0; i<slength; i++) begin
          $fwrite(spidata_file, "%02h ", rxBuf[i + 3]); 
          c_line = 0;
          if ((i+1)%16 == 0) begin
            $fwrite(spidata_file, "\n");
            c_line = 1;
          end
        end
      end
      if (c_line == 0) begin
        $fwrite(spidata_file, "\n");
      end
      c_line = 0;
    end
  end

endtask



`define INTERFACE_IDX       0 //internal spi
`define IF_IDX(idx)         ((`INTERFACE_IDX)+(idx))
`define IF_IQSPI(idx)       ((idx))
`define IF_OQSPI(idx)       ((10) + (idx))
`define IF_OSPI(idx)        ((5) + (idx))
`define SPI_WRITE           8'h0
`define SPI_READ            8'h1

initial begin

  #1000
  $fdisplay(spidata_file, "测试用例1-从IP中读取寄存器，上电后的寄存器期望值为0");
  spi_trans( (16'h00), (`SPI_READ), (128), (`IF_IQSPI(0)) );
  spi_trans( (16'h20), (`SPI_READ), (64), (`IF_IQSPI(1)) );
  spi_trans( (16'h20), (`SPI_READ), (64), (`IF_IQSPI(2)) );
  spi_trans( (16'h20), (`SPI_READ), (64), (`IF_IQSPI(3)) );
  spi_trans( (16'h20), (`SPI_READ), (64), (`IF_IQSPI(4)) );


  if ((`INTERFACE_IDX) == 5) begin
    $fdisplay(spidata_file, "\n\n从内部QSPI配置使用外部的SPI接口访问EasyBus");
    txBuf[0+3] = 8'h01;
    spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_IQSPI(0)) );
    spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_IQSPI(1)) );
    spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_IQSPI(2)) );
    spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_IQSPI(3)) );
    spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_IQSPI(4)) );
  end else if ((`INTERFACE_IDX) == 10) begin
    $fdisplay(spidata_file, "\n\n从内部QSPI配置使用外部的QSPI接口访问EasyBus");
    txBuf[0+3] = 8'h02;
    spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_IQSPI(0)) );
    spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_IQSPI(1)) );
    spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_IQSPI(2)) );
    spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_IQSPI(3)) );
    spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_IQSPI(4)) );
  end else begin
    $fdisplay(spidata_file, "\n\n从内部QSPI接口访问EasyBus");
  end


  //设置主站从站
  $fdisplay(spidata_file, "\n\n测试用例2-设置IP为主站或从站，并读取设置结果，期望：0主，1~4从");
  txBuf[0+3] = 8'h01;
  spi_trans( (16'h00), (`SPI_WRITE), (1), (`IF_IDX(0)) );

  #1000
  txBuf[0+3] = 8'h02;
  spi_trans( (16'h0), (`SPI_WRITE), (1), (`IF_IDX(1)) );
  
  #1000
  spi_trans( (16'h0), (`SPI_WRITE), (1), (`IF_IDX(2)) );
  
  #1000
  spi_trans( (16'h0), (`SPI_WRITE), (1), (`IF_IDX(3)) );
  
  #1000
  spi_trans( (16'h0), (`SPI_WRITE), (1), (`IF_IDX(4)) );

  $fdisplay(spidata_file, "--->>>设置完毕，检查接口寄存器");
  spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(0)) );
  spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(1)) );
  spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(2)) );
  spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(3)) );
  spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(4)) );

  //测试用例：

  //嗅探
  #10000
  $fdisplay(spidata_file, "\n\n测试用例3-发送嗅探包，需要在波形文件里检查");
  begin
    $fdisplay(spidata_file, "--->>>嗅探前，检查链路状态寄存器");
    //spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
    txBuf[0+3] = 8'h00;
    txBuf[1+3] = 8'h00;
    txBuf[2+3] = 8'h00;
    txBuf[3+3] = 8'h00;
    txBuf[4+3] = 8'h00;
    txBuf[5+3] = 8'h00;
    spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(1)) );
    txBuf[0+3] = 8'h00;
    txBuf[1+3] = 8'h00;
    txBuf[2+3] = 8'h00;
    txBuf[3+3] = 8'h00;
    txBuf[4+3] = 8'h00;
    txBuf[5+3] = 8'h00;
    spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(2)) );
    txBuf[0+3] = 8'h00;
    txBuf[1+3] = 8'h00;
    txBuf[2+3] = 8'h00;
    txBuf[3+3] = 8'h00;
    txBuf[4+3] = 8'h00;
    txBuf[5+3] = 8'h00;
    spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(3)) );
    txBuf[0+3] = 8'h00;
    txBuf[1+3] = 8'h00;
    txBuf[2+3] = 8'h00;
    txBuf[3+3] = 8'h00;
    txBuf[4+3] = 8'h00;
    txBuf[5+3] = 8'h00;
    spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(4)) );

    $fdisplay(spidata_file, "--->>>嗅探");
    //设置SM1在写入0x3地址触发enq
    txBuf[0+3] = 8'h03;
    txBuf[1+3] = 8'h00;
    spi_trans( (16'h0202), (`SPI_WRITE), (2), (`IF_IDX(0)) );

    //无子报文
    txBuf[0+3] = 8'h00;
    txBuf[1+3] = 8'h01;//heeader length 0 嗅探包1
    txBuf[2+3] = 8'h3f;
    txBuf[3+3] = 8'hff;
    spi_trans( (16'h1000), (`SPI_WRITE), (4), (`IF_IDX(0)) ); //写入SM1



    //发布请求
    txBuf[0+3] = 8'h04;
    txBuf[1+3] = 8'h00;
    spi_trans( (16'h21), (`SPI_WRITE), (2), (`IF_IDX(0)) );//写入长度

    txBuf[0+3] = 8'h01;
    spi_trans( (16'h20), (`SPI_WRITE), (1), (`IF_IDX(0)) );//发送SM0 接收SM0, 请求发送
    @(posedge isResp) #5 begin end

  end





  // 顺序索引
  #50000
  #50000
  #50000
  $fdisplay(spidata_file, "--->>>嗅探后，检查链路状态寄存器");
  //spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
  txBuf[0+3] = 8'h00;
    txBuf[1+3] = 8'h00;
    txBuf[2+3] = 8'h00;
    txBuf[3+3] = 8'h00;
    txBuf[4+3] = 8'h00;
    txBuf[5+3] = 8'h00;
  spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(1)) );
  txBuf[0+3] = 8'h00;
    txBuf[1+3] = 8'h00;
    txBuf[2+3] = 8'h00;
    txBuf[3+3] = 8'h00;
    txBuf[4+3] = 8'h00;
    txBuf[5+3] = 8'h00;
  spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(2)) );
  txBuf[0+3] = 8'h00;
    txBuf[1+3] = 8'h00;
    txBuf[2+3] = 8'h00;
    txBuf[3+3] = 8'h00;
    txBuf[4+3] = 8'h00;
    txBuf[5+3] = 8'h00;
  spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(3)) );
  txBuf[0+3] = 8'h00;
    txBuf[1+3] = 8'h00;
    txBuf[2+3] = 8'h00;
    txBuf[3+3] = 8'h00;
    txBuf[4+3] = 8'h00;
    txBuf[5+3] = 8'h00;
  spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(4)) );

  
  $fdisplay(spidata_file, "\n\n测试用例4-设置顺序索引");
  $display("index @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);

  begin
    $fdisplay(spidata_file, "--->>>设置顺序地址前，检查顺序地址");
    //spi_trans( (16'h0010), (`SPI_READ), (5), (`IF_IDX(0)) );
    spi_trans( (16'h0000), (`SPI_READ), (16), (`IF_IDX(1)) );
    spi_trans( (16'h0000), (`SPI_READ), (16), (`IF_IDX(2)) );
    spi_trans( (16'h0000), (`SPI_READ), (16), (`IF_IDX(3)) );
    spi_trans( (16'h0000), (`SPI_READ), (16), (`IF_IDX(4)) );


    $fdisplay(spidata_file, "--->>>设置顺序地址");
    //设置SM1在写入0xd地址触发enq
    txBuf[0+3] = 8'h0d;
    txBuf[1+3] = 8'h00;
    spi_trans( (16'h0202), (`SPI_WRITE), (2), (`IF_IDX(0)) );

    txBuf[0+3] = 8'h00;
    txBuf[1+3] = 8'ha0;//heeader length 10
    txBuf[2+3] = 8'h00;
    txBuf[3+3] = 8'h00;

    //子报文
    //设置顺序地址
    txBuf[4+3] = 8'h0; //设备索引
    txBuf[5+3] = 8'h0; //设备索引、类型
    txBuf[6+3] = $random; //地址
    txBuf[7+3] = $random; //地址
    txBuf[8+3] = 8'hd0;   //命令d 负载长度2
    txBuf[9+3] = 8'd02;   //负载长度2
    txBuf[10+3] = 8'h0;   //工作计数0
    txBuf[11+3] = 8'h0;   //工作计数0

    txBuf[12+3] = 8'h0;   //负载
    txBuf[13+3] = 8'h0;   //负载
    spi_trans( (16'h1000), (`SPI_WRITE), (14), (`IF_IDX(0)) ); //写入SM1



    //发布请求
    txBuf[0+3] = 8'h0e;
    txBuf[1+3] = 8'h00;
    spi_trans( (16'h21), (`SPI_WRITE), (2), (`IF_IDX(0)) );//写入长度

    txBuf[0+3] = 8'h01;
    spi_trans( (16'h20), (`SPI_WRITE), (1), (`IF_IDX(0)) );//发送SM0 接收SM0, 请求发送
    @(posedge isResp) #5 begin end
  end


  //测试

  spi_trans( (16'hc0), (`SPI_READ), (6), (3) );//发送SM0 接收SM0, 请求发送


  //读写
  #50000
  #50000
  #50000
  #50000
  $fdisplay(spidata_file, "--->>>设置顺序地址后，检查顺序地址");
  //spi_trans( (16'h0010), (`SPI_READ), (5), (`IF_IDX(0)) );
  spi_trans( (16'h0000), (`SPI_READ), (16), (`IF_IDX(1)) );
  spi_trans( (16'h0000), (`SPI_READ), (16), (`IF_IDX(2)) );
  spi_trans( (16'h0000), (`SPI_READ), (16), (`IF_IDX(3)) );
  spi_trans( (16'h0000), (`SPI_READ), (16), (`IF_IDX(4)) );

  $fdisplay(spidata_file, "\n\n测试用例5-交换数据");
  $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
  begin

    //设置SM1在写入516地址触发enq
    txBuf[0+3] = 8'h03;
    txBuf[1+3] = 8'h02;
    spi_trans( (16'h0202), (`SPI_WRITE), (2), (`IF_IDX(0)) );


    txBuf[0+3] = 8'h20;
    txBuf[1+3] = 8'h00;//heeader length 512
    txBuf[2+3] = 8'h00;
    txBuf[3+3] = 8'h00;

    //子报文
    txBuf[4+3] = 8'h0; 
    txBuf[5+3] = 8'h8; //index = 2
    txBuf[6+3] = 8'h08; //地址 //SM0
    txBuf[7+3] = 8'h30; //地址 //偏置
    txBuf[8+3] = 8'h20; //命令2 长度56
    txBuf[9+3] = 8'd56; //长度
    txBuf[10+3] = $random;
    txBuf[11+3] = $random;

    for( integer j = 0; j < 64-8; j = j + 1 ) begin
      @(posedge clock) #3 
      txBuf[12+3+j] = $random;
    end

    //-------------------------

    //子报文
    txBuf[68+3] = 8'h0; 
    txBuf[69+3] = 8'h4; //index = 1
    txBuf[70+3] = 8'h08; //地址 //SM0
    txBuf[71+3] = 8'h40; //地址 //偏置
    txBuf[72+3] = 8'h10; //命令1 长度56
    txBuf[73+3] = 8'd56; //长度
    txBuf[74+3] = $random;
    txBuf[75+3] = $random;

    for( integer j = 0; j < 64-8; j = j + 1 ) begin
      @(posedge clock) #3 
      txBuf[76+3+j] = $random;
    end

    //-------------------------

    //子报文
    txBuf[132+3] = 8'h0; 
    txBuf[133+3] = 8'hc; //index = 3
    txBuf[134+3] = 8'h10; //地址 //SM1
    txBuf[135+3] = 8'h40; //地址 //偏置
    txBuf[136+3] = 8'h00; //命令0 长度56
    txBuf[137+3] = 8'd56; //长度
    txBuf[138+3] = $random;
    txBuf[139+3] = $random;

    for( integer j = 0; j < 64-8; j = j + 1 ) begin
      @(posedge clock) #3 
      txBuf[140+3+j] = $random;
    end

    //-------------------------

    for( integer i = 0 ; i < 5; i = i + 1) begin
      //子报文
      txBuf[196+3+i*64+0] = $random;
      txBuf[196+3+i*64+1] = 8'h0; //index = random
      txBuf[196+3+i*64+2] = $random;
      txBuf[196+3+i*64+3] = $random;
      txBuf[196+3+i*64+4] = 8'h00; //命令0 长度56
      txBuf[196+3+i*64+5] = 8'd56; //长度
      txBuf[196+3+i*64+6] = $random;
      txBuf[196+3+i*64+7] = $random;

      for( integer j = 0; j < 64-8; j = j + 1 ) begin
        @(posedge clock) #3 
        txBuf[196+3+i*64+8+j] = $random;
      end
    end
    spi_trans( (16'h1000), (`SPI_WRITE), (516), (`IF_IDX(0)) ); //写入SM1



    //发布请求
    txBuf[0+3] = 8'h04;
    txBuf[1+3] = 8'h02;
    spi_trans( (16'h21), (`SPI_WRITE), (2), (`IF_IDX(0)) );//写入长度

    txBuf[0+3] = 8'h01;
    spi_trans( (16'h20), (`SPI_WRITE), (1), (`IF_IDX(0)) );//发送SM0 接收SM0, 请求发送
    @(posedge isResp) #5 begin end
  end



  // 同步
  #90000
  #90000
  #90000
  #90000
  #90000
  #90000
  #90000
  #90000
  #90000  
  #90000
  #90000
  #90000
  #90000
  #90000

  $display("sync @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
  begin



    //设置SM1在写入0x3地址触发enq
    txBuf[0+3] = 8'h17;
    txBuf[1+3] = 8'h00;
    spi_trans( (16'h0202), (`SPI_WRITE), (2), (`IF_IDX(0)) );

    txBuf[0+3] = 8'h01;
    txBuf[1+3] = 8'h40;//heeader length 20
    txBuf[2+3] = 8'h00;
    txBuf[3+3] = 8'h00;

    //子报文
    //设置同步
    txBuf[4+3] = 8'h0; //设备索引
    txBuf[5+3] = 8'h0; //设备索引、类型
    txBuf[6+3] = $random; //地址
    txBuf[7+3] = $random; //地址
    txBuf[8+3] = 8'he0;   //命令d 负载长度2
    txBuf[9+3] = 8'h0c;   //负载长度c
    txBuf[10+3] = 8'h0;   //工作计数0
    txBuf[11+3] = 8'h0;   //工作计数0

    txBuf[12+3] = 0;//timeStamp[7:0];   //负载
    txBuf[13+3] = 0;//timeStamp[15:8];   //负载
    txBuf[14+3] = 0;//timeStamp[23:16];   //负载
    txBuf[15+3] = 0;//timeStamp[31:24];   //负载
    txBuf[16+3] = 0;//timeStamp[39:32];   //负载
    txBuf[17+3] = 0;//timeStamp[47:40];   //负载
    txBuf[18+3] = 0;//timeStamp[55:48];   //负载
    txBuf[19+3] = 0;//timeStamp[63:56];   //负载

    txBuf[20+3] = 0;//s_ShinTop_Mst.masterParser.deltaTimeStamp[ 7: 0];   //负载
    txBuf[21+3] = 0;//s_ShinTop_Mst.masterParser.deltaTimeStamp[15: 8];   //负载
    txBuf[22+3] = 0;//s_ShinTop_Mst.masterParser.deltaTimeStamp[23:16];   //负载
    txBuf[23+3] = 0;//s_ShinTop_Mst.masterParser.deltaTimeStamp[31:24];   //负载

    spi_trans( (16'h1000), (`SPI_WRITE), (24), (`IF_IDX(0)) ); //写入SM1

    //写入替换时间戳替换地址
    txBuf[0+3] = 8'h0c;
    txBuf[1+3] = 8'hc0;
    spi_trans( (16'h24), (`SPI_WRITE), (2), (`IF_IDX(0)) ); //写入替换时间戳替换地址寄存器

    //发布请求
    txBuf[0+3] = 8'h18;
    txBuf[1+3] = 8'h00;
    spi_trans( (16'h21), (`SPI_WRITE), (2), (`IF_IDX(0)) );//写入长度

    txBuf[0+3] = 8'h01;
    spi_trans( (16'h20), (`SPI_WRITE), (1), (`IF_IDX(0)) );//发送SM0 接收SM0, 请求发送
    @(posedge isResp) #5 begin end

    //清除替换时间戳替换地址
    txBuf[0+3] = 8'h00;
    txBuf[1+3] = 8'h00;
    spi_trans( (16'h25), (`SPI_WRITE), (2), (`IF_IDX(0)) ); //清除替换时间戳替换地址寄存器



    //设定sync信号

    //设置SM1在写入51地址触发enq
    txBuf[0+3] = 8'd51;
    txBuf[1+3] = 8'h00;
    spi_trans( (16'h0202), (`SPI_WRITE), (2), (`IF_IDX(0)) );

    //header
    txBuf[0+3] = 8'h03;
    txBuf[1+3] = 8'h00;//heeader length 48
    txBuf[2+3] = 8'h00;
    txBuf[3+3] = 8'h00;

    //子报文
    //设置同步相关寄存器
    txBuf[4+3] = 8'h0; //设备索引
    txBuf[5+3] = 8'h08; //设备索引、类型 //2号设备
    txBuf[6+3] = 8'h01; //地址
    txBuf[7+3] = 8'h20; //地址 0x120
    txBuf[8+3] = 8'h10;   //命令1 写入寄存器 负载长度2
    txBuf[9+3] = 8'h28;   //负载长度0x28
    txBuf[10+3] = 8'h0;   //工作计数0
    txBuf[11+3] = 8'h0;   //工作计数0

    // txBuf[12+3] = 8'h0f;   //负载0x120 0x0f 全部脉冲，全部使能
    // txBuf[13+3] = 0;   //负载0x121
    // txBuf[14+3] = 10;  //负载0x122 sync0脉冲宽度 10
    // txBuf[15+3] = 0;   //负载0x123
    // txBuf[16+3] = 0;  //负载0x124 sync1脉冲宽度  0
    // txBuf[17+3] = 0;   //负载0x125
    // txBuf[18+3] = 1;   //负载0x126 sync2脉冲宽度 1
    // txBuf[19+3] = 0;   //负载0x127 
    // txBuf[20+3] = 8'hff;   //负载0x128 sync3脉冲宽度 最大
    // txBuf[21+3] = 8'hff;   //负载0x129


    txBuf[12+3] = 8'hff;   //负载0x120 0xff 全部电平，全部使能
    txBuf[13+3] = 0;   //负载0x121

    txBuf[14+3] = 0;  //负载0x122 sync0脉冲宽度
    txBuf[15+3] = 0;   //负载0x123
    txBuf[16+3] = 0;  //负载0x124 sync1脉冲宽度
    txBuf[17+3] = 0;   //负载0x125
    txBuf[18+3] = 0;   //负载0x126 sync2脉冲宽度
    txBuf[19+3] = 0;   //负载0x127 
    txBuf[20+3] = 0;   //负载0x128 sync3脉冲宽度
    txBuf[21+3] = 0;   //负载0x129

    txBuf[22+3] = 0;   //负载0x12a empty
    txBuf[23+3] = 0;   //负载0x12b
    txBuf[24+3] = 0;   //负载0x12c
    txBuf[25+3] = 0;   //负载0x12d
    txBuf[26+3] = 0;   //负载0x12e
    txBuf[27+3] = 0;   //负载0x12f

    //同步点
    txBuf[28+3] = 8'h90;   //负载0x130 同步点
    txBuf[29+3] = 8'h88;   //负载0x131
    txBuf[30+3] = 0;   //负载0x132
    txBuf[31+3] = 0;   //负载0x133
    txBuf[32+3] = 0;   //负载0x134
    txBuf[33+3] = 0;   //负载0x135
    txBuf[34+3] = 0;   //负载0x136
    txBuf[35+3] = 0;   //负载0x137

    //周期
    txBuf[36+3] = 8'hff;   //负载0x138
    txBuf[37+3] = 8'hf;   //负载0x139
    txBuf[38+3] = 0;   //负载0x13a
    txBuf[39+3] = 0;   //负载0x13b

    //0ffset sync1
    txBuf[40+3] = 8'ha;   //负载0x13c
    txBuf[41+3] = 0;   //负载0x13d
    txBuf[42+3] = 0;   //负载0x13e
    txBuf[43+3] = 0;   //负载0x13f

    //0ffset sync2
    txBuf[44+3] = 8'h0;   //负载0x140
    txBuf[45+3] = 0;   //负载0x141
    txBuf[46+3] = 0;   //负载0x142
    txBuf[47+3] = 0;   //负载0x143

    //0ffset sync3
    txBuf[48+3] = 8'h0;   //负载0x144
    txBuf[49+3] = 8'h01;   //负载0x145
    txBuf[50+3] = 0;   //负载0x146
    txBuf[51+3] = 0;   //负载0x147


    spi_trans( (16'h1000), (`SPI_WRITE), (52), (`IF_IDX(0)) ); //写入SM1

    //发布请求
    txBuf[0+3] = 8'd52;
    txBuf[1+3] = 8'h00;
    spi_trans( (16'h21), (`SPI_WRITE), (2), (`IF_IDX(0)) );//写入长度

    txBuf[0+3] = 8'h01;
    spi_trans( (16'h20), (`SPI_WRITE), (1), (`IF_IDX(0)) );//发送SM0 接收SM0, 请求发送
    @(posedge isResp) #5 begin end

  end

  //清脉冲
    //设置SM1在写入19地址触发enq
    txBuf[0+3] = 0;  //负载0x122 sync0脉冲宽度
    txBuf[1+3] = 0;  //负载0x123
    txBuf[2+3] = 0;  //负载0x124 sync1脉冲宽度
    txBuf[3+3] = 0;  //负载0x125
    txBuf[4+3] = 0;  //负载0x126 sync2脉冲宽度
    txBuf[5+3] = 0;  //负载0x127 
    txBuf[6+3] = 0;  //负载0x128 sync3脉冲宽度
    txBuf[7+3] = 0;  //负载0x129
    spi_trans( (16'h0122), (`SPI_WRITE), (8), (`IF_IDX(2)) ); //slv2



end


endmodule