用宏屏蔽不需要的测试用例

tb/shinTest/ShinTopSpiTb.v

@@ -503,8 +503,16 @@ endtask
 `define MST_RX_LEN_ADDR     (`MST_RX0_LEN_ADDR)
 `define MST_TX_LEN_ADDR     (`MST_TX0_LEN_ADDR)
 
-`define TEST_REG_RW
-
+`define ENABLE_REG_RW_TEST
+`define ENABLE_DET_TEST
+`define ENABLE_SET_ADDR_TEST
+//`define ENABLE_SM1_SEND_TEST
+`define ENABLE_EXCHG_DATA_SEQ_TEST
+  //`define ENABLE_EXCHG_DATA_SEQ0_TEST
+  //`define ENABLE_EXCHG_DATA_SEQ1_TEST
+  `define ENABLE_EXCHG_DATA_SEQ2_TEST
+  //`define ENABLE_EXCHG_DATA_BC_TEST
+//`define ENABLE_SYNC_TEST
 /*---------------------------------------------------------------------------------------------------------
 测试用例1
 ---------------------------------------------------------------------------------------------------------*/
@@ -512,7 +520,7 @@ initial begin
 
   #1000
 
-`ifdef TEST_REG_RW
+`ifdef ENABLE_REG_RW_TEST
 /*---------------------------------------------------------------------------------------------------------
 测试用例
 1. 从IP中读取寄存器，上电后的寄存器期望值为0
@@ -576,6 +584,7 @@ initial begin
   spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(3)) );
   spi_trans( (16'h00), (`SPI_READ), (1), (`IF_IDX(4)) );
 
+`ifdef ENABLE_DET_TEST
 /*---------------------------------------------------------------------------------------------------------
 测试用例3
 ---------------------------------------------------------------------------------------------------------*/
@@ -614,7 +623,7 @@ initial begin
     spi_trans( (`MST_RX_ADDR), (`SPI_READ), (`DEF_detect_pkt_len), (`IF_IDX(0)) );//读一下SM0的切换地址，将fifo弹出
 
   end
-
+`endif
 
   // 顺序索引
   //#50000
@@ -627,6 +636,7 @@ initial begin
   spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(3)) );
   spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(4)) );
 
+`ifdef ENABLE_SET_ADDR_TEST
 /*---------------------------------------------------------------------------------------------------------
 测试用例
 ---------------------------------------------------------------------------------------------------------*/
@@ -679,8 +689,9 @@ initial begin
   spi_trans( (16'h0000), (`SPI_READ), (16), (`IF_IDX(2)) );
   spi_trans( (16'h0000), (`SPI_READ), (16), (`IF_IDX(3)) );
   spi_trans( (16'h0000), (`SPI_READ), (16), (`IF_IDX(4)) );
+`endif
 
-
+`ifdef ENABLE_DET_TEST
 /*---------------------------------------------------------------------------------------------------------
 测试用例
 ---------------------------------------------------------------------------------------------------------*/
@@ -724,9 +735,10 @@ initial begin
   spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(2)) );
   spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(3)) );
   spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(4)) );
+`endif
 
 
-`ifdef ENABLE_CODE
+`ifdef ENABLE_SM1_SEND_TEST
   begin
     $fdisplay(spidata_file, "嗅探：使用SM1");
     $fdisplay(spidata_file, "--->>>嗅探前，检查链路状态寄存器");
@@ -766,6 +778,8 @@ initial begin
   spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(4)) );
 `endif
 
+
+`ifdef ENABLE_EXCHG_DATA_SEQ_TEST
 /*---------------------------------------------------------------------------------------------------------
 测试用例
 1. 交换数据sm0~sm7
@@ -775,9 +789,11 @@ initial begin
 4. 寄存器单读/写/读写，寄存器广播读/写/读写
 5. 以上交换数据的错误形式
 ---------------------------------------------------------------------------------------------------------*/
-  #1000
   $fdisplay(spidata_file, "\n\n测试用例：交换数据");
+  `ifdef ENABLE_EXCHG_DATA_SEQ0_TEST
+  #1000
   $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
+  
   begin
     $fdisplay(spidata_file, "--->>>交换数据sm0~sm7");
     
@@ -797,7 +813,9 @@ initial begin
     $fdisplay(spidata_file, ">>回包：");
     spi_trans( (`MST_RX_ADDR), (`SPI_READ), (`DEF_seq_0_pkt_len), (`IF_IDX(0)) );//读一下SM0的切换地址，将fifo弹出
   end
+  `endif
 
+  `ifdef ENABLE_EXCHG_DATA_SEQ1_TEST
   #1000
   $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
   begin
@@ -824,8 +842,9 @@ initial begin
     spi_trans( (16'h0800), (`SPI_READ), (64), (`IF_IDX(2)) );
     spi_trans( (16'h2800), (`SPI_READ), (64), (`IF_IDX(3)) );
     spi_trans( (16'h3800), (`SPI_READ), (64), (`IF_IDX(4)) );
+  `endif
 
-
+  `ifdef ENABLE_EXCHG_DATA_SEQ2_TEST
   #1000
   $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
   begin
@@ -885,8 +904,12 @@ initial begin
     $fdisplay(spidata_file, ">>回包：");
     spi_trans( (`MST_RX_ADDR), (`SPI_READ), (`DEF_seq_2_pkt_len), (`IF_IDX(0)) );//读一下SM0的切换地址，将fifo弹出
   end
+`endif
+`endif
 
+`ifdef ENABLE_EXCHG_DATA_BC_TEST
   #1000
+  $fdisplay(spidata_file, "\n\n测试用例：广播交换数据");
   $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
   begin
     $fdisplay(spidata_file, "\n--->>>广播读");
@@ -934,7 +957,10 @@ initial begin
     spi_trans( (16'h0800), (`SPI_READ), (32), (`IF_IDX(2)) );
     spi_trans( (16'h0800), (`SPI_READ), (32), (`IF_IDX(3)) );
     spi_trans( (16'h0800), (`SPI_READ), (32), (`IF_IDX(4)) );
+`endif
 
+
+`ifdef ENABLE_SYNC_TEST
 /*---------------------------------------------------------------------------------------------------------
 测试用例
 1. 测试 同步(sync) 和 同步输出 (sync_out)
@@ -1023,6 +1049,8 @@ initial begin
     txBuf[0+3] = 8'h01;
     spi_trans( (16'h40), (`SPI_WRITE), (1), (`IF_IDX(0)) );//复位主站
     spi_trans( (16'h40), (`SPI_WRITE), (1), (`IF_IDX(1)) );//复位从站2
+`endif
+
 end