大部分测试用例通过
This commit is contained in:
@@ -1,35 +1,5 @@
|
||||
`timescale 1 ns / 1 ps
|
||||
|
||||
`define ENABLE_REG_RW1_TEST "generated/log/reg_rw1_tc.log"
|
||||
//`define ENABLE_ENCRYPTION
|
||||
//`define ENABLE_DET1_TEST "generated/log/det1_tc.log"
|
||||
//`define ENABLE_DET2_TEST "generated/log/det2_tc.log"
|
||||
//`define ENABLE_SET_ADDR_TEST "generated/log/set_addr_tc.log"
|
||||
//`define ENABLE_INT_INIT_TEST "generated/log/int_init_tc.log"
|
||||
//`define ENABLE_DET_ERR1_TEST "generated/log/det_err1_tc.log"
|
||||
//`define ENABLE_SMx_SEND1_TEST "generated/log/sm_send1_tc.log"
|
||||
//`define ENABLE_SMx_SEND2_TEST "generated/log/sm_send2_tc.log"
|
||||
//`define ENABLE_SMx_SEND3_TEST "generated/log/sm_send3_tc.log"
|
||||
//`define ENABLE_ERR_PKT1_TEST "generated/log/err_pkt1_tc.log"
|
||||
//`define ENABLE_ERR_PKT2_TEST "generated/log/err_pkt2_tc.log"
|
||||
//`define ENABLE_ERR_PKT3_TEST "generated/log/err_pkt3_tc.log"
|
||||
|
||||
//`define ENABLE_EXCHG_DATA_SEQ0_TEST "generated/log/exchg_data_seq0_tc.log"
|
||||
//`define ENABLE_EXCHG_DATA_SEQ1_TEST "generated/log/exchg_data_seq1_tc.log"
|
||||
//`define ENABLE_EXCHG_DATA_SEQ2_TEST "generated/log/exchg_data_seq2_tc.log"
|
||||
//`define ENABLE_EXCHG_DATA_SEQ3_TEST "generated/log/exchg_data_seq3_tc.log"
|
||||
|
||||
//`define ENABLE_BC_R_TEST "generated/log/bc_r_tc.log"
|
||||
//`define ENABLE_BC_W_TEST "generated/log/bc_w_tc.log"
|
||||
//`define ENABLE_BC_RW_TEST "generated/log/bc_rw_tc.log"
|
||||
|
||||
//`define ENABLE_SYNC_TEST "generated/log/sync_tc.log"
|
||||
//`define ENABLE_SYNC_SIG0_TEST "generated/log/sync_sig0_tc.log"
|
||||
//`define ENABLE_SYNC_SIG1_TEST "generated/log/sync_sig1_tc.log"
|
||||
//`define ENABLE_RESET_TEST "generated/log/reset_tc.log"
|
||||
|
||||
//`define ENABLE_WD1_TEST "generated/log/wd1_tc.log"
|
||||
|
||||
module ShinTopSpiTb(
|
||||
|
||||
);
|
||||
@@ -415,7 +385,11 @@ initial begin
|
||||
reset <= 0;
|
||||
|
||||
//#20000000
|
||||
#1000000000
|
||||
#1000000000
|
||||
`ifdef USING_OSPI
|
||||
#1000000000
|
||||
#1000000000
|
||||
`endif
|
||||
//#5000000
|
||||
|
||||
$display("Time Out !!!");
|
||||
@@ -943,30 +917,6 @@ task wait_comm_finished(input [16:0] dev_idx);
|
||||
st = $realtime;
|
||||
is_run = 1;
|
||||
|
||||
`ifdef enable_wait_clear_int
|
||||
txBuf[0] = 8'h00;
|
||||
txBuf[1] = 8'h78;
|
||||
txBuf[2] = `SPI_WRITE;
|
||||
txBuf[3] = 8'h03;
|
||||
txBuf[4] = 8'h00;
|
||||
txBuf[5] = 8'h00;
|
||||
txBuf[6] = 8'h00;
|
||||
|
||||
length = 8'h07;
|
||||
idx = dev_idx;
|
||||
|
||||
#5
|
||||
@(negedge sck)
|
||||
isReq <= 1;
|
||||
@(posedge sck) #5
|
||||
isReq <= 0;
|
||||
|
||||
@( negedge isBusy) #1000
|
||||
begin
|
||||
|
||||
end
|
||||
`endif
|
||||
|
||||
while (is_run == 1) begin
|
||||
txBuf[0] = 8'h00;
|
||||
txBuf[1] = 8'h74;
|
||||
@@ -1019,162 +969,6 @@ initial begin
|
||||
|
||||
#1000
|
||||
|
||||
`ifdef ENABLE_REG_RW1_TEST
|
||||
/*---------------------------------------------------------------------------------------------------------
|
||||
测试用例
|
||||
1. 从IP中读取寄存器，上电后的寄存器期望值为0
|
||||
---------------------------------------------------------------------------------------------------------*/
|
||||
begin:READ_REG_TESTCASE
|
||||
`BEGIN_TESTCASE(`ENABLE_REG_RW1_TEST);
|
||||
_t_start = $realtime;
|
||||
$fdisplay(spidata_file, "测试用例：从IP中读取寄存器，上电后的寄存器期望值为0");
|
||||
`SPI_TRANS( (16'h00), (`SPI_READ), (64), (`IF_OSPI(0)) );
|
||||
`SPI_TRANS( (16'h00), (`SPI_READ), (64), (`IF_OSPI(1)) );
|
||||
`SPI_TRANS( (16'h00), (`SPI_READ), (64), (`IF_OSPI(2)) );
|
||||
`SPI_TRANS( (16'h00), (`SPI_READ), (64), (`IF_OSPI(3)) );
|
||||
`SPI_TRANS( (16'h00), (`SPI_READ), (64), (`IF_OSPI(4)) );
|
||||
_t_end = $realtime;
|
||||
$fdisplay(spidata_file, "该测试用例运行时间：%t\n", _t_end - _t_start);
|
||||
`END_TESTCASE(`ENABLE_REG_RW1_TEST);
|
||||
end
|
||||
`endif
|
||||
|
||||
begin:SETTING_INTERFACE
|
||||
if ((`INTERFACE_IDX) == `ALL_DEV_NUM) begin
|
||||
$fdisplay(spidata_file, "\n\n从SPI配置使用SPI接口访问EasyBus");
|
||||
txBuf[3] = 8'h01;
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(0)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(1)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(2)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(3)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(4)) );
|
||||
end else if ((`INTERFACE_IDX) == (`ALL_DEV_NUM * 2)) begin
|
||||
$fdisplay(spidata_file, "\n\n从SPI配置使用2 QSPI接口访问EasyBus");
|
||||
txBuf[3] = 8'h02;
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(0)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(1)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(2)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(3)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(4)) );
|
||||
end else if ((`INTERFACE_IDX) == (`ALL_DEV_NUM * 3)) begin
|
||||
$fdisplay(spidata_file, "\n\n从SPI配置使用ASPI接口访问EasyBus");
|
||||
txBuf[3] = 8'h03;
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(0)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(1)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(2)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(3)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(4)) );
|
||||
end else begin
|
||||
$fdisplay(spidata_file, "\n\n从SPI配置使用0 QSPI接口访问EasyBus");
|
||||
txBuf[3] = 8'h00;
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(0)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(1)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(2)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(3)) );
|
||||
spi_trans( (16'h09), (`SPI_WRITE), (1), (`IF_OSPI(4)) );
|
||||
end
|
||||
end
|
||||
|
||||
`ifdef ENABLE_INT_INIT_TEST
|
||||
begin:CHECK_INTERRUPT_SIG
|
||||
$fdisplay(spidata_file, "\n\n测试用例：检查设备的INTERRUPT信号");
|
||||
|
||||
@(posedge clock) begin
|
||||
if (io_int_sig[0]) $fdisplay(spidata_file, "**MST Interrupt.");
|
||||
if (io_int_sig[1]) $fdisplay(spidata_file, "**SLV0 Interrupt.");
|
||||
if (io_int_sig[2]) $fdisplay(spidata_file, "**SLV1 Interrupt.");
|
||||
if (io_int_sig[3]) $fdisplay(spidata_file, "**SLV2 Interrupt.");
|
||||
if (io_int_sig[4]) $fdisplay(spidata_file, "**SLV3 Interrupt.");
|
||||
end
|
||||
|
||||
$fdisplay(spidata_file, "-检查中断");
|
||||
spi_trans( (16'h70), (`SPI_READ), (14), (`IF_IDX(0)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (14), (`IF_IDX(1)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (14), (`IF_IDX(2)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (14), (`IF_IDX(3)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (14), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-清中断");
|
||||
txBuf[`ARRAY_IDX_OFF+0] = 8'h00;
|
||||
txBuf[`ARRAY_IDX_OFF+1] = 8'h00;
|
||||
txBuf[`ARRAY_IDX_OFF+2] = 8'h00;
|
||||
txBuf[`ARRAY_IDX_OFF+3] = 8'h80;
|
||||
spi_trans( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(0)) );
|
||||
spi_trans( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(1)) );
|
||||
spi_trans( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(2)) );
|
||||
spi_trans( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(3)) );
|
||||
spi_trans( (16'h78), (`SPI_WRITE), (4), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-检查中断");
|
||||
spi_trans( (16'h70), (`SPI_READ), (14), (`IF_IDX(0)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (14), (`IF_IDX(1)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (14), (`IF_IDX(2)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (14), (`IF_IDX(3)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (14), (`IF_IDX(4)) );
|
||||
|
||||
end
|
||||
|
||||
begin:CHECK_INTERRUPT_CFG_REG
|
||||
$fdisplay(spidata_file, "\n\n测试用例：检查设备的INTERRUPT信号设置寄存器");
|
||||
|
||||
$fdisplay(spidata_file, "-检查中断");
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(0)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-设置中断");
|
||||
txBuf[`ARRAY_IDX_OFF+0] = 8'h00;
|
||||
txBuf[`ARRAY_IDX_OFF+1] = 8'h00;
|
||||
txBuf[`ARRAY_IDX_OFF+2] = 8'h00;
|
||||
txBuf[`ARRAY_IDX_OFF+3] = 8'h00;
|
||||
spi_trans( (16'h70), (`SPI_WRITE), (4), (`IF_IDX(0)) );
|
||||
spi_trans( (16'h70), (`SPI_WRITE), (4), (`IF_IDX(1)) );
|
||||
spi_trans( (16'h70), (`SPI_WRITE), (4), (`IF_IDX(2)) );
|
||||
spi_trans( (16'h70), (`SPI_WRITE), (4), (`IF_IDX(3)) );
|
||||
spi_trans( (16'h70), (`SPI_WRITE), (4), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-检查中断");
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(0)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-设置中断");
|
||||
txBuf[`ARRAY_IDX_OFF+0] = 8'h0F;
|
||||
txBuf[`ARRAY_IDX_OFF+1] = 8'h00;
|
||||
txBuf[`ARRAY_IDX_OFF+2] = 8'h00;
|
||||
txBuf[`ARRAY_IDX_OFF+3] = 8'h00;
|
||||
spi_trans( (16'h70), (`SPI_WRITE), (4), (`IF_IDX(0)) );
|
||||
|
||||
txBuf[`ARRAY_IDX_OFF+0] = 8'h00;
|
||||
txBuf[`ARRAY_IDX_OFF+1] = 8'hFF;
|
||||
txBuf[`ARRAY_IDX_OFF+2] = 8'h00;
|
||||
txBuf[`ARRAY_IDX_OFF+3] = 8'h00;
|
||||
spi_trans( (16'h70), (`SPI_WRITE), (4), (`IF_IDX(1)) );
|
||||
spi_trans( (16'h70), (`SPI_WRITE), (4), (`IF_IDX(2)) );
|
||||
spi_trans( (16'h70), (`SPI_WRITE), (4), (`IF_IDX(3)) );
|
||||
spi_trans( (16'h70), (`SPI_WRITE), (4), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-检查中断");
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(0)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(1)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(2)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(3)) );
|
||||
spi_trans( (16'h70), (`SPI_READ), (4), (`IF_IDX(4)) );
|
||||
|
||||
$fdisplay(spidata_file, "-中断改为脉冲模式");
|
||||
txBuf[`ARRAY_IDX_OFF+0] = 8'h10;
|
||||
txBuf[`ARRAY_IDX_OFF+1] = 8'h8A;
|
||||
spi_trans( (16'h7c), (`SPI_WRITE), (2), (`IF_IDX(0)) );
|
||||
spi_trans( (16'h7c), (`SPI_WRITE), (2), (`IF_IDX(1)) );
|
||||
spi_trans( (16'h7c), (`SPI_WRITE), (2), (`IF_IDX(2)) );
|
||||
spi_trans( (16'h7c), (`SPI_WRITE), (2), (`IF_IDX(3)) );
|
||||
spi_trans( (16'h7c), (`SPI_WRITE), (2), (`IF_IDX(4)) );
|
||||
end
|
||||
`endif
|
||||
|
||||
`include "tc_runlist.vh"
|
||||
|
||||
|
||||
Reference in New Issue
Block a user