增加新的测试用例,用来测试主站的其他SMx

tb/shinTest/ShinTopSpiTb.v

@@ -1,9 +1,10 @@
 `timescale 1 ns / 1 ps
 
-//`define ENABLE_REG_RW_TEST
+`define ENABLE_REG_RW_TEST
 `define ENABLE_DET_TEST
 `define ENABLE_SET_ADDR_TEST
 //`define ENABLE_SM1_SEND_TEST
+//`define ENABLE_SMx_SEND_TEST
 `define ENABLE_EXCHG_DATA_SEQ_TEST
   //`define ENABLE_EXCHG_DATA_SEQ0_TEST
   //`define ENABLE_EXCHG_DATA_SEQ1_TEST
@@ -37,6 +38,8 @@ module ShinTopSpiTb(
     integer c_line;
     integer _pos;
     integer _len;
+    integer _t_start;
+    integer _t_end;
 
     wire [4:0] isSoftReset;
 
@@ -223,31 +226,46 @@ initial begin
 	reset <= 0;
 
 `ifdef ENABLE_REG_RW_TEST
+  #1000000
+`endif
 
+`ifdef ENABLE_DET_TESTENABLE_SM1_SEND_TEST
+  #900000
 `endif
-`ifdef ENABLE_DET_TEST
+
-`endif
 `ifdef ENABLE_SET_ADDR_TEST
+  #900000
 `endif
 
 `ifdef ENABLE_SM1_SEND_TEST
+    #500000
 `endif
+
+`ifdef ENABLE_SMx_SEND_TEST
+  #1000000
+`endif
+
 `ifdef ENABLE_EXCHG_DATA_SEQ_TEST
   `ifdef ENABLE_EXCHG_DATA_SEQ0_TEST
+    #3500000
   `endif
   `ifdef ENABLE_EXCHG_DATA_SEQ1_TEST
+    #3500000
   `endif
   `ifdef ENABLE_EXCHG_DATA_SEQ2_TEST
+    #6000000
   `endif
   `ifdef ENABLE_EXCHG_DATA_BC_TEST
+    #2000000
   `endif
 `endif
 `ifdef ENABLE_SYNC_TEST
+    #3000000
+  #500000
 `endif
 
-
 //#20000000
-#5000000
+#1000000
 
 	$display("Time Out !!!");
   	$fclose(spidata_file);
@@ -552,12 +570,15 @@ initial begin
 测试用例
 1. 从IP中读取寄存器，上电后的寄存器期望值为0
 ---------------------------------------------------------------------------------------------------------*/
+  _t_start = $time;
   $fdisplay(spidata_file, "测试用例：从IP中读取寄存器，上电后的寄存器期望值为0");
   spi_trans( (16'h00), (`SPI_READ), (64), (`IF_IQSPI(0)) );
   spi_trans( (16'h00), (`SPI_READ), (64), (`IF_IQSPI(1)) );
   spi_trans( (16'h00), (`SPI_READ), (64), (`IF_IQSPI(2)) );
   spi_trans( (16'h00), (`SPI_READ), (64), (`IF_IQSPI(3)) );
   spi_trans( (16'h00), (`SPI_READ), (64), (`IF_IQSPI(4)) );
+  _t_end = $time;
+  $fdisplay(spidata_file, "该测试用例运行时间：%2tns", (_t_end - _t_start) / 1000);
 `endif
 
 
@@ -615,9 +636,9 @@ initial begin
 /*---------------------------------------------------------------------------------------------------------
 测试用例3
 ---------------------------------------------------------------------------------------------------------*/
-
   //嗅探
-  #10000
+  _t_start = $time;
+  #1000
   $fdisplay(spidata_file, "\n\n测试用例：发送嗅探包，需要在波形文件里检查");
   begin
     $fdisplay(spidata_file, "--->>>嗅探前，检查链路状态寄存器");
@@ -650,23 +671,25 @@ initial begin
     spi_trans( (`MST_RX_ADDR), (`SPI_READ), (`DEF_detect_pkt_len), (`IF_IDX(0)) );//读一下SM0的切换地址，将fifo弹出
 
   end
-`endif
 
   // 顺序索引
   //#50000
-  #50000
+  #1000
-  #50000
   $fdisplay(spidata_file, "--->>>嗅探后，检查链路状态寄存器");
   //spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
   spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(1)) );
   spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(2)) );
   spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(3)) );
   spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(4)) );
+  _t_end = $time;
+  $fdisplay(spidata_file, "该测试用例运行时间：%2tns", (_t_end - _t_start) / 1000);
+`endif
 
 `ifdef ENABLE_SET_ADDR_TEST
 /*---------------------------------------------------------------------------------------------------------
 测试用例
 ---------------------------------------------------------------------------------------------------------*/
+  _t_start = $time;
   $fdisplay(spidata_file, "\n\n测试用例：设置顺序索引");
   $display("index @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
 
@@ -716,6 +739,9 @@ initial begin
   spi_trans( (16'h0000), (`SPI_READ), (16), (`IF_IDX(2)) );
   spi_trans( (16'h0000), (`SPI_READ), (16), (`IF_IDX(3)) );
   spi_trans( (16'h0000), (`SPI_READ), (16), (`IF_IDX(4)) );
+
+  _t_end = $time;
+  $fdisplay(spidata_file, "该测试用例运行时间：%2tns", (_t_end - _t_start) / 1000);
 `endif
 
 `ifdef ENABLE_DET_TEST
@@ -723,6 +749,7 @@ initial begin
 测试用例
 ---------------------------------------------------------------------------------------------------------*/
   //嗅探
+  _t_start = $time;
   #1000
   $fdisplay(spidata_file, "\n\n测试用例：发送嗅探包，需要在波形文件里检查");
   begin
@@ -762,18 +789,21 @@ initial begin
   spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(2)) );
   spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(3)) );
   spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(4)) );
+  _t_end = $time;
+  $fdisplay(spidata_file, "该测试用例运行时间：%2tns", (_t_end - _t_start) / 1000);
 `endif
 
 
 `ifdef ENABLE_SM1_SEND_TEST
+  _t_start = $time;
   begin
-    $fdisplay(spidata_file, "嗅探：使用SM1");
+    $fdisplay(spidata_file, "\n嗅探：使用SM1");
     $fdisplay(spidata_file, "--->>>嗅探前，检查链路状态寄存器");
     //spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
-    spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(1)) );
+    spi_trans( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
-    spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(2)) );
+    spi_trans( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
-    spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(3)) );
+    spi_trans( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
-    spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(4)) );
+    spi_trans( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
 
     $fdisplay(spidata_file, "--->>>嗅探");
     //设置SM1在写入0x3地址触发enq
@@ -795,16 +825,49 @@ initial begin
     spi_trans( (`MST_RX1_ADDR), (`SPI_READ), (`DEF_detect_pkt_len), (`IF_IDX(0)) );//读一下SM0的切换地址，将fifo弹出
   end
 
-
   // 顺序索引
   $fdisplay(spidata_file, "--->>>嗅探后，检查链路状态寄存器");
-  //spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(0)) );
+  //spi_trans( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(0)) );
-  spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(1)) );
+  spi_trans( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(1)) );
-  spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(2)) );
+  spi_trans( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(2)) );
-  spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(3)) );
+  spi_trans( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(3)) );
-  spi_trans( (16'h00c0), (`SPI_READ), (6), (`IF_IDX(4)) );
+  spi_trans( (16'h00c0), (`SPI_READ), (4), (`IF_IDX(4)) );
+
 `endif
 
+`ifdef ENABLE_SMx_SEND_TEST
+  #1000
+  $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
+  begin
+    $fdisplay(spidata_file, "\n广播写：使用SM3");
+    $fdisplay(spidata_file, "--->>>SM3广播写");
+
+    `include "sm3_pkt.vh"
+
+    `DEF_sm3_pkt_sm(txBuf);
+    spi_trans( (`MST_TX3_LEN_ADDR), (`SPI_WRITE), (2), (`IF_IDX(0)) );
+    spi_trans( (`MST_RX3_LEN_ADDR), (`SPI_WRITE), (2), (`IF_IDX(0)) );
+
+    $fdisplay(spidata_file, "<<发包：");
+    `DEF_sm3_pkt(txBuf);
+    spi_trans( (`MST_TX3_ADDR), (`SPI_WRITE), (`DEF_sm3_pkt_len), (`IF_IDX(0)) ); //写入SM1
+    //发布请求 
+    txBuf[0+3] = `MST_TX_TRIGGER(3);//`MST_TX_TRG;//`MST_TX_TRIGGER(1);
+    spi_trans( (16'h20), (`SPI_WRITE), (1), (`IF_IDX(0)) );//发送SM0 接收SM0, 请求发送
+    @(posedge isResp) #5 begin end
+
+    $fdisplay(spidata_file, ">>回包：");
+    spi_trans( (`MST_RX3_ADDR), (`SPI_READ), (`DEF_sm3_pkt_len), (`IF_IDX(0)) );//读一下SM0的切换地址，将fifo弹出
+  end
+  spi_trans( (16'h0800), (`SPI_READ), (16), (`IF_IDX(1)) );
+  spi_trans( (16'h0800), (`SPI_READ), (16), (`IF_IDX(2)) );
+  spi_trans( (16'h0800), (`SPI_READ), (16), (`IF_IDX(3)) );
+  spi_trans( (16'h0800), (`SPI_READ), (16), (`IF_IDX(4)) );
+
+
+  _t_end = $time;
+  $fdisplay(spidata_file, "该测试用例运行时间：%2tns", (_t_end - _t_start) / 1000);
+`endif
 
 `ifdef ENABLE_EXCHG_DATA_SEQ_TEST
 /*---------------------------------------------------------------------------------------------------------
@@ -818,6 +881,7 @@ initial begin
 ---------------------------------------------------------------------------------------------------------*/
   $fdisplay(spidata_file, "\n\n测试用例：交换数据");
   `ifdef ENABLE_EXCHG_DATA_SEQ0_TEST
+  _t_start = $time;
   #1000
   $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
   
@@ -840,9 +904,12 @@ initial begin
     $fdisplay(spidata_file, ">>回包：");
     spi_trans( (`MST_RX_ADDR), (`SPI_READ), (`DEF_seq_0_pkt_len), (`IF_IDX(0)) );//读一下SM0的切换地址，将fifo弹出
   end
+  _t_end = $time;
+  $fdisplay(spidata_file, "该测试用例运行时间：%2tns", (_t_end - _t_start) / 1000);
   `endif
 
   `ifdef ENABLE_EXCHG_DATA_SEQ1_TEST
+  _t_start = $time;
   #1000
   $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
   begin
@@ -869,9 +936,13 @@ initial begin
   spi_trans( (16'h0800), (`SPI_READ), (64), (`IF_IDX(2)) );
   spi_trans( (16'h2800), (`SPI_READ), (64), (`IF_IDX(3)) );
   spi_trans( (16'h3800), (`SPI_READ), (64), (`IF_IDX(4)) );
+  
+  _t_end = $time;
+  $fdisplay(spidata_file, "该测试用例运行时间：%2tns", (_t_end - _t_start) / 1000);
   `endif
 
   `ifdef ENABLE_EXCHG_DATA_SEQ2_TEST
+  _t_start = $time;
   #1000
   $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
   begin
@@ -931,10 +1002,14 @@ initial begin
     $fdisplay(spidata_file, ">>回包：");
     spi_trans( (`MST_RX_ADDR), (`SPI_READ), (`DEF_seq_2_pkt_len), (`IF_IDX(0)) );//读一下SM0的切换地址，将fifo弹出
   end
+  _t_end = $time;
+  $fdisplay(spidata_file, "该测试用例运行时间：%2tns", (_t_end - _t_start) / 1000);
 `endif
+
 `endif
 
 `ifdef ENABLE_EXCHG_DATA_BC_TEST
+  _t_start = $time;
   #1000
   $fdisplay(spidata_file, "\n\n测试用例：广播交换数据");
   $display("read&write @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
@@ -945,7 +1020,8 @@ initial begin
     `DEF_bc_r_pkt_sm(txBuf);
     spi_trans( (`MST_TX_LEN_ADDR), (`SPI_WRITE), (2), (`IF_IDX(0)) );
     spi_trans( (`MST_RX_LEN_ADDR), (`SPI_WRITE), (2), (`IF_IDX(0)) );
-
+`ifdef ENABLE_EXCHG_DATA_BC_TEST
+`endif
     $fdisplay(spidata_file, "<<发包：");
     `DEF_bc_r_pkt(txBuf);
     spi_trans( (`MST_TX_ADDR), (`SPI_WRITE), (`DEF_bc_r_pkt_len), (`IF_IDX(0)) ); //写入SM1
@@ -984,6 +1060,9 @@ initial begin
   spi_trans( (16'h0800), (`SPI_READ), (32), (`IF_IDX(2)) );
   spi_trans( (16'h0800), (`SPI_READ), (32), (`IF_IDX(3)) );
   spi_trans( (16'h0800), (`SPI_READ), (32), (`IF_IDX(4)) );
+  
+  _t_end = $time;
+  $fdisplay(spidata_file, "该测试用例运行时间：%2tns", (_t_end - _t_start) / 1000);
 `endif
 
 
@@ -993,6 +1072,7 @@ initial begin
 1. 测试 同步(sync) 和 同步输出 (sync_out)
 ---------------------------------------------------------------------------------------------------------*/
   // 同步
+  _t_start = $time;
   #1000
 
   $display("sync @ %d", s_ShinTop_Mst.interface__io_cReg_timeStamp);
@@ -1045,7 +1125,6 @@ initial begin
     spi_trans( (`MST_RX_ADDR), (`SPI_READ), (`DEF_sync_sig_pkt_len), (`IF_IDX(0)) );//读一下SM0的切换地址，将fifo弹出
   end
 
-
   //spi_trans( (16'h0100), (`SPI_READ), (32), (`IF_IDX(0)) );
   spi_trans( (16'h0100), (`SPI_READ), (32), (`IF_IDX(1)) );
   spi_trans( (16'h0130), (`SPI_READ), (32), (`IF_IDX(1)) );
@@ -1076,6 +1155,9 @@ initial begin
   txBuf[0+3] = 8'h01;
   spi_trans( (16'h40), (`SPI_WRITE), (1), (`IF_IDX(0)) );//复位主站
   spi_trans( (16'h40), (`SPI_WRITE), (1), (`IF_IDX(1)) );//复位从站2
+
+  _t_end = $time;
+  $fdisplay(spidata_file, "该测试用例运行时间：%2tns", (_t_end - _t_start) / 1000);
 `endif
 
 end

tb/shinTest/gen_pkt.py

@@ -220,7 +220,7 @@ if __name__ == '__main__':
     genPkt.gen("./generated/shin/seq_1_pkt.vh", 1)
     
     #-------------------------------------------------------------------------
-    #>>>>>>读
+    #>>>>>>普通数据包2
     genPkt.clean()
     genPkt.setPktType(0)
     
@@ -237,6 +237,25 @@ if __name__ == '__main__':
     genPkt.gen("./generated/shin/seq_2_pkt.vh", 1)
 
 
+    #-------------------------------------------------------------------------
+    #>>>>>>交换数据 SMx
+    genPkt.clean()
+    genPkt.setPktType(0)
+    
+    #subPkt参数：索引、索引类型、地址、命令、长度、数据
+    data = bytearray(b"\0" * 10)
+    data[0] = 16
+    data[1] = 0
+    genPkt.addSubPkt(random.randint(0, 2048), 0, 0x0302, 0xe, 2, data) #0x030a, 0xe, 2, data)
+    
+    data = bytearray(b"\0"*100)
+    for i in range(100):
+        data[i] = i + 1
+    genPkt.addSubPkt(random.randint(0, 2048), 0, 0x0800, 0xe, 16, data) #0x1800, 0xe, 16, data)
+
+    genPkt.gen("./generated/shin/sm3_pkt.vh", 1)
+    
+    
     #-------------------------------------------------------------------------
     #>>>>>>同步数据包
     genPkt.clean()
@@ -331,3 +350,6 @@ if __name__ == '__main__':
 
     
     
+    
+
+